Planet

SGS-6340-48T4S

box_SGS-6340-48T4S
SGS-6340-48T4S undefined
Layer 3 48-Port 10/100/1000T + 4-Port 1000X SFP Stackable Managed Switch
3icon_L3_RIP_Routing 2icon_L3-Static-Routing 4icon_L3_OSPF_Routing 1icon_IPv6-Management

  • Powerful Layer 3 Gigabit Routing Solution for Enterprise Backbone and Data Center Networking
    PLANET SGS-6340-48T4S is a Layer 3 Stackable Managed Gigabit Switch that provides high-density performance,Layer 3 static routing, RIP (Routing Information Protocol) and OSPF (Open Shortest Path First). With104Gbps switching fabric, the SGS-6340-48T4S can handle extremely large amounts of data in a secure topology linking to an enterprise backbone or high capacity servers. The powerful WRR (Weighted Round Robin) and Network Security features make the SGS-6340-48T4S perform effective data traffic control for ISP and enterprise VoIP, video streaming, and multicast applications.
    Layer 3 Routing Support
    The SGS-6340-48T4S enables the administrator to conveniently boost network efficiency by configuring Layer 3 static routing manually, the RIP (Routing Information Protocol) or OSPF (Open Shortest Path First) settings automatically. The RIP can employ the hop count as a routing metric and prevent routing loops by implementing a limit on the number of hops allowed in a path from the source to a destination. The maximum number of hops allowed for the RIP is 15. The OSPF is an interior dynamic routing protocol for autonomous system based on link-state. The protocol creates a link-state database by exchanging link-states among Layer3 switches, and then uses the Shortest Path First algorithm to generate a route table based on that database.

    Abundant IPv6 Support
    The SGS-6340-48T4S provides IPv6 management and enterprise-level secure features such as SSH, ACL, WRRand RADIUS authentication. The SGS-6340-48T4S thus helps the enterprises to step in the IPv6 era with the lowest investment. In addition, you don’t need to replace the network facilities when the IPv6 FTTx edge network is built.

    High Performance
    The SGS-6340-48T4S provides 48 10/100/1000Mbps Gigabit Ethernet ports with 4 additional Gigabit SFP slots. It boasts a high-performance switch architecture that is capable of providing non-blocking switch fabric and wire-speed throughput as high as 104Gbps, which greatly simplifies the tasks of upgrading the LAN for catering to increasing bandwidth demands.

    Robust Layer 2 Features
    The SGS-6340-48T4S can be programmed for basic switch management functions such as port speed configuration, port aggregation, VLAN, Spanning Tree Protocol, WRR, bandwidth control and IGMP snooping. The SGS-6340-48T4S provides 802.1Q tagged VLAN, Q-in-Q, voice VLAN and GVRP Protocol. The VLAN groups allowed to be on the SGS-6340-48T4S will be maximally up to 256. By supporting port aggregation, the SGS-6340-48T4S allows the operation of a high-speed trunk combined with multiple ports. It enables up to 128 groups for trunking with a maximum of 8 ports for each group.

    Excellent Traffic Control
    The SGS-6340-48T4S is loaded with powerful traffic management and WRR features to enhance services offered by telecoms. The WRR functionalities include wire-speed Layer 4 traffic classifiers and bandwidth limitation which are particularly useful for multi-tenant unit, multi-business unit, Telco, or network service applications. It also empowers the enterprises to take full advantage of the limited network resources and guarantees the best performance at VoIP and video conferencing transmission.

    Powerful Security
    The SGS-6340-48T4S supports ACL policies comprehensively. The traffic can be classified by source/destination IP addresses, source/destination MAC addresses, IP protocols, TCP/UDP, IP precedence, time ranges and ToS. Moreover, various policies can be conducted to forward the traffic. The SGS-6340-48T4S also provides IEEE 802.1x port based access authentication, which can be deployed with RADIUS, to ensure the port level security and block illegal users.

    Efficient Management
    The SGS-6340-48T4S supports IP stacking function that helps network managers to easily configure up to 24 switches in the same series via one single IP address instead of connecting and setting each unit one by one. For efficient management, the SGS-6340-48T4S Managed Gigabit Switch is equipped with console, Web and SNMP management interfaces. With its built-in Web-based management interface, the SGS-6340-48T4S offers an easy-to-use, platform-independent management and configuration facility. The SGS-6340-48T4S supports standard Simple Network Management Protocol (SNMP) and can be managed via any standard-based management software. For text-based management, the SGS-6340-48T4S can be accessed via Telnet and the console port. Moreover, the SGS-6340-48T4S offers secure remote management by supporting SSH connection which encrypts the packet content at each session.

    Flexibility and Extension Solution
    The four mini-GBIC slots built in the SGS-6340-48T4S are compatible with 1000BASE-X and WDM SFP (Small Form-factor Pluggable) fiber-optic modules. The distance can be extended from 550 meters (multi-mode fiber) to 10/50/70/120 kilometers (single-mode fiber or WDM fiber). They are well suited for applications within the enterprise data centers and distributions.

    Ordering Information
    SGS-6340-48T4S Layer 3 48-Port 10/100/1000T + 4-Port 1000X SFP Stackable Managed Switch


  • Server Farm Switch
    The SGS-6340-48T4S provides up to 52 Gigabit Ethernet ports for enterprises and network servers. It is ideal to be used as a server farm switch connecting to servers. With its port trunking function, an 8GB fat pipe is provided for connecting to the backbone if required.
    Enterprise Security and QoS Edge Switch
    With the IEEE 802.1x network access authentication, the SGS-6340-48T4S provides the MAC/IP/Protocol Access Control list and Port Security functions which can limit the number of MAC addresses to be passed through one specific port. The IGMP snooping and QoS features in the SGS-6340-48T4S improve the network efficiency and protect the network clients.
    Layer 3 VLAN Routing
    With the built-in robust Layer 3 traffic routing protocols, the SGS-6340-48T4S ensures reliable routing between VLANs and network segments. The routing protocols can be applied via VLAN interface. The SGS-6340-48T4S is certainly a cost-effective and ideal solution for enterprises.
    Ordering Information
    SGS-6340-48T4S Layer 3 48-Port 10/100/1000T + 4-Port 1000X SFP Stackable Managed Switch


  • Hardware Specifications
    Copper Ports 48 10/ 100/1000BASE-T RJ45 auto-MDI/MDI-X ports
    SFP/mini-GBIC Slots 4 1000BASE-X SFP interfaces
    Console 1 x RJ45-to-RS232 serial port (9600, 8, N, 1)
    Switch Architecture Store-and-forward
    Switch Fabric 104Gbps/non-blocking
    Switch Throughput 77.38Mpps
    Address Table 16K MAC address table with auto learning function
    Shared Data Buffer 1.5Mbytes
    Flow Control Back pressure for half-duplex
    IEEE 802.3x pause frame for full-duplex
    Jumbo Frame 9K bytes
    LED System:
    PWR, SYS
    Ports:
    10/100/1000T RJ45 Port: LNK/ACT
    1000X SFP slot: LNK/ACT
    Dimensions (W x D x H) 442 x 280 x 44 mm, 1U height
    Weight 3702g
    Power Consumption 38 watts/129 BTU (maximum)
    Power Requirements AC 100~240V, 50/60Hz
    Management Function
    System Configuration Console, Telnet, SSH, Web browser, SNMP v1, v2c and v3
    Management Supports both IPv4 and IPv6 addressing
    Supports the user IP security inspection for IPv4/IPv6 SNMP
    Supports MIB and TRAP
    Supports IPv4/IPv6 FTP/TFTP
    Supports IPv4/IPv6 NTP
    Supports RMOM 1, 2, 3, 9 four groups
    Supports the RADIUS authentication for IPv4/IPv6 Telnet user name and password
    Supports IPv4/IPv6 SSH
    The right configuration for users to adopt RADIUS server’s shell management
    Supports CLI, console, Telnet
    Supports SNMPv1/v2c/v3
    Supports Security IP safety net management function: avoid unlawful landing at nonrestrictive area
    Supports Syslog server for IPv4 and IPv6
    Supports TACACS+
    Layer 3 Function
    Routing Protocol Static routing, RIP and OSPF
    Routing Table 128
    Layer 2 Function
    Port Configuration Port disable/enable
    Auto-negotiation 10/100/1000Mbps full and half duplex mode selection
    Flow control disable/enable
    Bandwidth control on each port
    Port loopback detect
    Port Status Display each port’s speed duplex mode, link status, flow control status and
    auto negotiation status
    VLAN 802.1Q tagged based VLAN, up to 256 VLAN groups
    802.1ad Q-in-Q (VLAN stacking)
    GVRP for VLAN management
    Private VLAN Edge (PVE) supported
    Protocol-based VLAN
    MAC-based VLAN
    IP subnet VLAN
    Bandwidth Control TX/RX/both
    Link Aggregation IEEE 802.3ad LACP/static trunk
    Supports 128 groups with 8 ports per trunk group
    QoS 8 priority queues on all switch ports
    Supports strict priority and Weighted Round Robin (WRR) CoS policies
    Traffic classification:
    – IEEE 802.1p CoS/ToS
    – IPv4/IPv6 DSCP
    – Port-based WRR
    Multicast IGMP v1/v2/v3 snooping
    Querier mode support
    MLD v1/v2 snooping
    Querier mode support
    Multicast VLAN Register (MVR)
    Access Control List Supports Standard and Expanded ACL
    IP-based ACL/MAC-based ACL
    Time-based ACL
    Up to 512 entries
    Bandwidth Control At least 64Kbps step
    Security Supports MAC + port binding
    IPv4/IPv6 + MAC + port binding
    IPv4/IPv6 + port binding
    Supports MAC filter
    ARP scanning prevention
    Authentication IEEE 802.1x port-based network access control
    AAA authentication: TACACS+ and IPv4/IPv6 over RADIUS
    SNMP MIBs RFC 1213 MIB-II
    RFC 1215 Internet Engineering Task Force
    RFC 1271 RMON
    RFC 1354 IP-Forwarding MIB
    RFC 1493 Bridge MIB
    RFC 1643 Ether-like MIB
    RFC 1907 SNMP v2
    RFC 2011 IP/ICMP MIB
    RFC 2012 TCP MIB
    RFC 2013 UDP MIB
    RFC 2096 IP forward MIB
    RFC 2233 if MIB
    RFC 2452 TCP6 MIB
    RFC 2454 UDP6 MIB
    RFC 2465 IPv6 MIB
    RFC 2466 ICMP6 MIB
    RFC 2573 SNMPV3 notify
    RFC 2574 SNMPV3 vacm
    RFC 2674 Bridge MIB Extensions (IEEE 802.1Q MIB)
    RFC 2674 Bridge MIB Extensions (IEEE 802.1P MIB)
    Standard Conformance
    Regulatory Compliance FCC Part 15 Class A, CE
    Standards Compliance IEEE 802.3 10BASE-T
    IEEE 802.3u 100BASE-TX
    IEEE 802.3z Gigabit 1000BASE-SX/LX
    IEEE 802.3ab Gigabit 1000BASE-T
    IEEE 802.3x flow control and back pressure
    IEEE 802.3ad port trunk with LACP
    IEEE 802.1D Spanning Tree Protocol
    IEEE 802.1w Rapid Spanning Tree Protocol
    IEEE 802.1s Multiple Spanning Tree Protocol
    IEEE 802.1p Class of Service
    IEEE 802.1Q VLAN tagging
    IEEE 802.1X port authentication network control
    IEEE 802.1ab LLDP
    RFC 768 UDP
    RFC 793 TFTP
    RFC 791 IP
    RFC 792 ICMP
    RFC 2068 HTTP
    RFC 1112 IGMP version 1
    RFC 2236 IGMP version 2
    RFC 3376 IGMP version 3
    RFC 2710 MLD version 1
    FRC 3810 MLD version 2
    RFC 2328 OSPF v2
    RFC 1058 RIP v1
    RFC 2453 RIP v2
    Environment
    Operating Temperature: 0 ~ 50 degrees C
    Relative Humidity: 5 ~ 90% (non-condensing)
    Storage Temperature: -10 ~ 70 degrees C
    Relative Humidity: 5 ~ 90% (non-condensing)
    Ordering Information
    SGS-6340-48T4S Layer 3 48-Port 10/100/1000T + 4-Port 1000X SFP Stackable Managed Switch

Facebooktwittergoogle_pluspinterestlinkedinyoutube

SGS-6340-24T4S

box_SGS-6340-24T4S
SGS-6340-24T4S undefined
Layer 3 24-Port 10/100/1000T + 4-Port 1000X SFP Stackable Managed Switch
3icon_L3_RIP_Routing 2icon_L3-Static-Routing 4icon_L3_OSPF_Routing 1icon_IPv6-Management

  • Powerful Layer 3 Gigabit Routing Solution for Enterprise Backbone and Data Center Networking
    PLANET SGS-6340-24T4S is a Layer 3 Stackable Managed Gigabit Switch that provides high-density performance,Layer 3 static routing, RIP (Routing Information Protocol) and OSPF (Open Shortest Path First). With56Gbps switching fabric, the SGS-6340-24T4S can handle extremely large amounts of data in a secure topology linking to an enterprise backbone or high capacity servers. The powerful WRR (Weighted Round Robin) and Network Security features make the SGS-6340-24T4S perform effective data traffic control for ISP and enterprise VoIP, video streaming, and multicast applications.
    Layer 3 Routing Support
    The SGS-6340-24T4S enables the administrator to conveniently boost network efficiency by configuring Layer 3 static routing manually, the RIP (Routing Information Protocol) or OSPF (Open Shortest Path First) settings automatically. The RIP can employ the hop count as a routing metric and prevent routing loops by implementing a limit on the number of hops allowed in a path from the source to a destination. The maximum number of hops allowed for the RIP is 15. The OSPF is an interior dynamic routing protocol for autonomous system based on link-state. The protocol creates a link-state database by exchanging link-states among Layer3 switches, and then uses the Shortest Path First algorithm to generate a route table based on that database.

    Abundant IPv6 Support
    The SGS-6340-24T4S provides IPv6 management and enterprise-level secure features such as SSH, ACL, WRRand RADIUS authentication. The SGS-6340-24T4S thus helps the enterprises to step in the IPv6 era with the lowest investment. In addition, you don’t need to replace the network facilities when the IPv6 FTTx edge network is built.

    High Performance
    The SGS-6340-24T4S boasts a high-performance switch architecture that is capable of providing non-blocking switch fabric and wire-speed throughput as high as 56Gbps, which greatly simplifies the tasks of upgrading the LAN for catering to increasing bandwidth demands.

    Robust Layer 2 Features
    The SGS-6340-24T4S can be programmed for basic switch management functions such as port speed configuration, port aggregation, VLAN, Spanning Tree Protocol, WRR, bandwidth control and IGMP snooping. The SGS-6340-24T4S provides 802.1Q tagged VLAN, Q-in-Q, voice VLAN and GVRP Protocol. The VLAN groups allowed to be on the SGS-6340-24T4S will be maximally up to 256. By supporting port aggregation, the SGS-6340-24T4S allows the operation of a high-speed trunk combined with multiple ports. It enables up to 128 groups for trunking with a maximum of 8 ports for each group.

    Excellent Traffic Control
    The SGS-6340-24T4S is loaded with powerful traffic management and WRR features to enhance services offered by telecoms. The WRR functionalities include wire-speed Layer 4 traffic classifiers and bandwidth limitation which are particularly useful for multi-tenant unit, multi-business unit, Telco, or network service applications. It also empowers the enterprises to take full advantage of the limited network resources and guarantees the best in VoIP and video conferencing transmission.Powerful Security
    The SGS-6340-24T4S supports ACL policies comprehensively. The traffic can be classified by source/destination IP addresses, source/destination MAC addresses, IP protocols, TCP/UDP, IP precedence, time ranges and ToS. Moreover, various policies can be conducted to forward the traffic. The SGS-6340-24T4S also provides IEEE 802.1x port based access authentication, which can be deployed with RADIUS, to ensure the port level security and block illegal users.

    Efficient Management
    The SGS-6340-24T4S supports IP stacking function that helps network managers to easily configure up to 24 switches in the same series via one single IP address instead of connecting and setting each unit one by one. For efficient management, the SGS-6340-24T4S Managed Gigabit Switch is equipped with console, Web and SNMP management interfaces. With its built-in Web-based management interface, the SGS-6340-24T4S offers an easy-to-use, platform-independent management and configuration facility. The SGS-6340-24T4S supports standard Simple Network Management Protocol (SNMP) and can be managed via any standard-based management software. For text-based management, the SGS-6340-24T4S can be accessed via Telnet and the console port. Moreover, the SGS-6340-24T4S offers secure remote management by supporting SSH connection which encrypts the packet content at each session.

    Flexibility and Extension Solution
    The four mini-GBIC slots built in the SGS-6340-24T4S are compatible with 1000BASE-X and WDM SFP (Small Form-factor Pluggable) fiber-optic modules. The distance can be extended from 550 meters (multi-mode fiber) to 10/50/70/120 kilometers (single-mode fiber or WDM fiber). They are well suited for applications within the enterprise data centers and distributions.

    Ordering Information
    SGS-6340-24T4S Layer 3 24-Port 10/100/1000T + 4-Port 1000X SFP Stackable Managed Switch


  • Server Farm Switch
    The SGS-6340-24T4S provides up to 28 Gigabit Ethernet ports for enterprises and network servers. It is ideal to be used as a server farm switch connecting to servers. With its port trunking function, an 8GB fat pipe is provided for connecting to the backbone if required.
    undefined
    Enterprise Security and QoS Edge Switch
    With the IEEE 802.1x network access authentication, the SGS-6340-24T4S provides the MAC/IP/Protocol Access Control list and Port Security functions which can limit the number of MAC addresses to be passed through one specific port. The IGMP snooping and QoS features in the SGS-6340-24T4S improve the network efficiency and protect the network clients.
    Layer 3 VLAN Routing
    With the built-in robust Layer 3 traffic routing protocols, the SGS-6340-24T4S ensures reliable routing between VLANs and network segments. The routing protocols can be applied via VLAN interface. The SGS-6340-24T4S is certainly a cost-effective and ideal solution for enterprises.
    Ordering Information
    SGS-6340-24T4S Layer 3 24-Port 10/100/1000T + 4-Port 1000X SFP Stackable Managed Switch


  • Hardware Specifications
    Copper Ports 24 10/100/1000BASE-T RJ45 auto-MDI/MDI-X ports
    SFP/mini-GBIC Slots 4 1000BASE-X SFP interfaces
    Console 1 x RJ45-to-RS232 serial port (9600, 8, N, 1)
    Switch Architecture Store-and-forward
    Switch Fabric 56Gbps/non-blocking
    Switch Throughput 41.66Mpps
    Address Table 16K MAC address table with auto learning function
    Shared Data Buffer 1.5MB
    Flow Control Back pressure for half-duplex
    IEEE 802.3x pause frame for full-duplex
    Jumbo Frame 9KB
    LED System:
    PWR, SYS
    Ports:
    10/100/1000T RJ45 Port: LNK/ACT
    1000X SFP slot: LNK/ACT
    Dimensions (W x D x H) 442 x 220 x 44 mm, 1U height
    Weight 2340g
    Power Consumption 19.2 watts/65.51 BTU (maximum)
    Power Requirements AC 100~240V, 50/60Hz
    Management Function
    System Configuration Console, Telnet, SSH, Web browser, SNMP v1, v2c and v3
    Management Supports both IPv4 and IPv6 addressing
    Supports the user IP security inspection for IPv4/IPv6 SNMP
    Supports MIB and TRAP
    Supports IPv4/IPv6 FTP/TFTP
    Supports IPv4/IPv6 NTP
    Supports RMON 1, 2, 3, 9 four groups
    Supports the RADIUS authentication for IPv4/IPv6 Telnet user name and password
    Supports IPv4/IPv6 SSH
    The right configuration for users to adopt RADIUS server’s shell management
    Supports CLI, console, Telnet
    Supports SNMP v1, v2c and v3
    Supports Security IP safety net management function: avoid unlawful landing at nonrestrictive area
    Supports Syslog server for IPv4 and IPv6
    Supports TACACS+
    Layer 3 Function
    Routing Protocol Static routing, RIP and OSPF
    Routing Table 128
    Layer 2 Function
    Port Configuration Port disable/enable
    Auto-negotiation 10/100/1000Mbps full and half duplex mode selection
    Flow control disable/enable
    Bandwidth control on each port
    Port loopback detect
    Port Status Display each port’s speed duplex mode, link status, flow control status and
    auto negotiation status
    VLAN 802.1Q tagged based VLAN, up to 256 VLAN groups
    802.1ad Q-in-Q (VLAN stacking)
    GVRP for VLAN management
    Private VLAN Edge (PVE) supported
    Protocol-based VLAN
    MAC-based VLAN
    IP subnet VLAN
    Bandwidth Control TX/RX/both
    Link Aggregation IEEE 802.3ad LACP/static trunk
    Supports 128 groups with 8 ports per trunk group
    QoS 8 priority queues on all switch ports
    Supports strict priority and Weighted Round Robin (WRR) CoS policies
    Traffic classification:
    – IEEE 802.1p CoS/ToS
    – IPv4/IPv6 DSCP
    – Port-based WRR
    Multicast IGMP v1/v2/v3 snooping
    Querier mode support
    MLD v1/v2 snooping
    Multicast VLAN Register (MVR)
    Access Control List Supports Standard and Expanded ACL
    IP-based ACL/MAC-based ACL
    Time-based ACL
    Up to 512 entries
    Bandwidth Control At least 64Kbps step
    Security Supports MAC + port binding
    IPv4/IPv6 + MAC + port binding
    IPv4/IPv6 + port binding
    Supports MAC filter
    ARP scanning prevention
    Authentication IEEE 802.1x port-based network access control
    AAA authentication: TACACS+ and IPv4/IPv6 over RADIUS
    SNMP MIBs RFC 1213 MIB-II
    RFC 1215 Internet Engineering Task Force
    RFC 1271 RMON
    RFC 1354 IP-Forwarding MIB
    RFC 1493 Bridge MIB
    RFC 1643 Ether-like MIB
    RFC 1907 SNMP v2
    RFC 2011 IP/ICMP MIB
    RFC 2012 TCP MIB
    RFC 2013 UDP MIB
    RFC 2096 IP forward MIB
    RFC 2233 if MIB
    RFC 2452 TCP6 MIB
    RFC 2454 UDP6 MIB
    RFC 2465 IPv6 MIB
    RFC 2466 ICMP6 MIB
    RFC 2573 SNMP v3 notify
    RFC 2574 SNMP v3 vacm
    RFC 2674 Bridge MIB Extensions (IEEE 802.1Q MIB)
    RFC 2674 Bridge MIB Extensions (IEEE 802.1P MIB)
    Standard Conformance
    Regulatory Compliance FCC Part 15 Class A, CE
    Standards Compliance IEEE 802.3 10BASE-T
    IEEE 802.3u 100BASE-TX
    IEEE 802.3z Gigabit 1000BASE-SX/LX
    IEEE 802.3ab Gigabit 1000BASE-T
    IEEE 802.3x flow control and back pressure
    IEEE 802.3ad port trunk with LACP
    IEEE 802.1D Spanning Tree Protocol
    IEEE 802.1w Rapid Spanning Tree Protocol
    IEEE 802.1s Multiple Spanning Tree Protocol
    IEEE 802.1p Class of Service
    IEEE 802.1Q VLAN tagging
    IEEE 802.1X port authentication network control
    IEEE 802.1ab LLDP
    RFC 768 UDP
    RFC 793 TFTP
    RFC 791 IP
    RFC 792 ICMP
    RFC 2068 HTTP
    RFC 1112 IGMP v1
    RFC 2236 IGMP v2
    RFC 3376 IGMP v3
    RFC 2710 MLD v1
    FRC 3810 MLD v2
    RFC 2328 OSPF v2
    RFC 1058 RIP v1
    RFC 2453 RIP v2
    Environment
    Operating Temperature: 0 ~ 50 degrees C
    Relative Humidity: 5 ~ 90% (non-condensing)
    Storage Temperature: -10 ~ 70 degrees C
    Relative Humidity: 5 ~ 90% (non-condensing)
    Ordering Information
    SGS-6340-24T4S Layer 3 24-Port 10/100/1000T + 4-Port 1000X SFP Stackable Managed Switch

Facebooktwittergoogle_pluspinterestlinkedinyoutube

SGS-6340-24P4S

box_SGS-6340-24P4S
SGS-6340-24P4S undefined
4-Slot Layer 3 IPv6/IPv4 Routing Chassis Switch
3icon_L3_RIP_Routing 4icon_L3_OSPF_Routing 4icon_SSL-SSH 0icon_snmp 1icon_IPv6-Management 8icon_802.3at_802.3af_End-span

  • Powerful Layer 3 Gigabit Routing and Power over Ethernet Solution
    PLANET SGS-6340-24P4S is a Layer 3 PoE Stackable Managed Gigabit Switch that provides high-density performance, Layer 3 static routing, RIP (Routing Information Protocol) and OSPF (Open Shortest Path First). With 56Gbps switching fabric, the SGS-6340-24P4S can handle extremely large amounts of data in a secure topology linking to an enterprise backbone or high capacity servers. The powerful WRR (Weighted Round Robin) and Network Security features make the SGS-6340-24P4S perform effective data traffic control for ISP and enterprise VoIP, video streaming, and multicast applications. The SGS-6340-24P4S has 24 IEEE 802.3at PoE+ ports and PoE budget up to 370 watts for catering to medium to large scale of VoIP or IP Surveillance networks at a lower total cost.
    Centralized Power Management for Gigabit Ethernet PoE Networking
    To fulfill the needs of higher power required PoE network applications with Gigabit speed transmission, the SGS-6340-24P4S features high-performance Gigabit IEEE 802.3af PoE (up to 15.4 watts) and IEEE 802.3at PoE+ (up to 30 watts) on all ports. It perfectly meets the power requirement of PoE VoIP phone and all kinds of PoE IP cameras such as IR, PTZ, speed dome cameras or even box type IP cameras with built-in fan and heater.

    The SGS-6340-24P4S’s PoE capabilities also help to reduce deployment costs for network devices as a result of freeing from restrictions of power outlet locations. Power and data switching are integrated into one unit, delivered over a single cable and managed centrally. It thus eliminates cost for additional AC wiring and reduces installation time.

    PoE Schedule for Energy Saving
    Besides being used for IP surveillance, the SGS-6340-24P4S is certainly applicable to build any PoE network including VoIP and wireless LAN. Under the trend of energy saving worldwide and contributing to the environmental protection on the Earth, the SGS-6340-24P4S can effectively control the power supply besides its capability of giving high watts power. The “PoE schedule” function helps you to enable or disable PoE power feeding for each PoE port during specified time intervals and it is a powerful function to help SMBs or enterprises save energy and budget

    Layer 3 Routing Support
    The SGS-6340-24P4S enables the administrator to conveniently boost network efficiency by configuring Layer 3 static routing manually, the RIP (Routing Information Protocol) or OSPF (Open Shortest Path First) settings automatically. The RIP can employ the hop count as a routing metric and prevent routing loops by implementing a limit on the number of hops allowed in a path from the source to a destination. The maximum number of hops allowed for the RIP is 15. The OSPF is an interior dynamic routing protocol for autonomous system based on link-state. The protocol creates a link-state database by exchanging link-states among Layer 3 switches, and then uses the Shortest Path First algorithm to generate a route table based on that database.

    Abundant IPv6 Support
    The SGS-6340-24P4S provides IPv6 management and enterprise-level secure features such as SSH, ACL, WRRand RADIUS authentication. The SGS-6340-24P4S thus helps the enterprises to step in the IPv6 era with the lowest investment. In addition, you don’t need to replace the network facilities when the IPv6 FTTx edge network is built.

    High Performance
    The SGS-6340-24P4S boasts a high-performance switch architecture that is capable of providing non-blocking switch fabric and wire-speed throughput as high as 56Gbps, which greatly simplifies the tasks of upgrading the LAN for catering to increasing bandwidth demands.

    Robust Layer 2 Features
    The SGS-6340-24P4S can be programmed for basic switch management functions such as port speed configuration, port aggregation, VLAN, Spanning Tree Protocol, WRR, bandwidth control and IGMP snooping. The SGS-6340-24P4S provides 802.1Q tagged VLAN, Q-in-Q, voice VLAN and GVRP Protocol. The VLAN groups allowed to be on the SGS-6340-24P4S will be maximally up to 256. By supporting port aggregation, the SGS-6340-24P4S allows the operation of a high-speed trunk combined with multiple ports. It enables up to 128 groups for trunking with a maximum of 8 ports for each group.

    Excellent Traffic Control
    The SGS-6340-24P4S is loaded with powerful traffic management and WRR features to enhance services offered by telecoms. The WRR functionalities include wire-speed Layer 4 traffic classifiers and bandwidth limitation which are particularly useful for multi-tenant unit, multi-business unit, Telco, or network service applications. It also empowers the enterprises to take full advantage of the limited network resources and guarantees the best performance in VoIP and video conferencing transmission.

    Powerful Security
    The SGS-6340-24P4S supports ACL policies comprehensively. The traffic can be classified by source/destination IP addresses, source/destination MAC addresses, IP protocols, TCP/UDP, IP precedence, time ranges and ToS. Moreover, various policies can be conducted to forward the traffic. The SGS-6340-24P4S also provides IEEE 802.1x port based access authentication, which can be deployed with RADIUS, to ensure the port level security and block illegal users.

    Efficient Management
    The SGS-6340-24P4S supports IP stacking function that helps network managers to easily configure up to 24 switches in the same series via one single IP address instead of connecting and setting each unit one by one. For efficient management, the SGS-6340-24P4S Managed Gigabit Switch is equipped with console, Web and SNMP management interfaces. With its built-in Web-based management interface, the SGS-6340-24P4S offers an easy-to-use, platform-independent management and configuration facility. The SGS-6340-24P4S supports standard Simple Network Management Protocol (SNMP) and can be managed via any standard-based management software. For text-based management, the SGS-6340-24P4S can be accessed via Telnet and the console port. Moreover, the SGS-6340-24P4S offers secure remote management by supporting SSH connection which encrypts the packet content at each session.

    Flexibility and Extension Solution
    The four mini-GBIC slots built in the SGS-6340-24P4S are compatible with 1000BASE-X and WDM SFP (Small Form-factor Pluggable) fiber-optic modules. The distance can be extended from 550 meters (multi-mode fiber) to 10/50/70/120 kilometers (single-mode fiber or WDM fiber). They are well suited for applications within the enterprise data centers and distributions.

    Ordering Information
    SGS-6340-24P4S Layer 3 24-Port 10/100/1000T 802.3at PoE + 4-Port 1000X SFP Stackable Managed Switch (370W)


  • High Scalability & Best Security for Today’s IP Networking and Cyber Security Solution
    The SGS-6340-24P4S comes with non-blocking design and SFP fiber-optic modules, bringing network infrastructure higher flexibility but lower in cost. Providing twenty-four 10/100/1000BASE-T PoE+ ports and four Gigabit SFP ports, the SGS-6340-24P4S can easily build a secure network on the cyber security system for the enterprises. For instance, it can work with the router and UTM to perform comprehensive security protection for today’s businesses.
    undefined
    Layer 3 VLAN Routing
    With the built-in robust Layer 3 traffic routing protocols, the SGS-6340-24P4S ensures reliable routing between VLANs and network segments. The routing protocols can be applied via VLAN interface. The SGS-6340-24P4S is certainly a cost-effective and ideal solution for enterprises.
    undefined
    Ordering Information
    SGS-6340-24P4S Layer 3 24-Port 10/100/1000T 802.3at PoE + 4-Port 1000X SFP Stackable Managed Switch (370W)


  • Hardware Specifications
    Copper Ports 24 10/100/1000BASE-T RJ45 auto-MDI/MDI-X ports
    SFP/mini-GBIC Slots 4 1000BASE-X SFP interfaces
    PoE Injector Port 24 ports with 802.3at/af PoE injector function with port-1 to port-24
    Console 1 x RJ45-to-RS232 serial port (9600, 8, N, 1)
    Switch Architecture Store-and-forward
    Switch Fabric 56Gbps/non-blocking
    Switch Throughput 41.66Mpps
    Address Table 16K MAC address table with auto learning function
    Shared Data Buffer 1.5MB
    Flow Control Back pressure for half-duplex
    IEEE 802.3x pause frame for full-duplex
    Jumbo Frame 9KB
    LED System:
    PWR, SYS
    Ports:
    10/100/1000T RJ45 Port: Button off: LNK/ACT, Button on: PoE In-Use
    1000X SFP slot: LNK/ACT
    Dimensions (W x D x H) 442 x 330 x 44 mm, 1U height
    Weight 4503g
    Power Consumption 449 watts/1532.05 BTU (maximum)
    Power Requirements AC 100~240V, 50/60Hz
    Fan 3
    Power over Ethernet
    PoE Standard IEEE 802.3af/802.3at PoE+ PSE
    PoE Power Supply Type End-span
    PoE Power Output Per port 54V DC, 33 watts (max.)
    Power Pin Assignment 1/2(+), 3/6(-)
    PoE Power Budget 370 watts (max.)
    PoE Ability PD @ 9 watts 24 units
    PoE Ability PD @ 15 watts 24 units
    PoE Ability PD @ 30 watts 12 units
    Management Function
    System Configuration Console, Telnet, SSH, Web browser, SNMP v1, v2c and v3
    Management Supports both IPv4 and IPv6 addressing
    Supports the user IP security inspection for IPv4/IPv6 SNMP
    Supports MIB and TRAP
    Supports IPv4/IPv6 FTP/TFTP
    Supports IPv4/IPv6 NTP
    Supports RMON 1, 2, 3, 9 four groups
    Supports the RADIUS authentication for IPv4/IPv6 Telnet user name and password
    Supports IPv4/IPv6 SSH
    The right configuration for users to adopt RADIUS server’s shell management
    Supports CLI, console, Telnet
    Supports SNMP v1, v2c and v3
    Supports Security IP safety net management function: avoid unlawful landing at nonrestrictive area
    Supports Syslog server for IPv4 and IPv6
    Supports TACACS+
    Layer 3 Function
    Routing Protocol Static routing, RIP and OSPF
    Routing Table 128
    Layer 2 Function
    Port Configuration Port disable/enable
    Auto-negotiation 10/100/1000Mbps full and half duplex mode selection
    Flow control disable/enable
    Bandwidth control on each port
    Port loopback detect
    Port Status Display each port’s speed duplex mode, link status, flow control status and
    auto negotiation status
    VLAN 802.1Q tagged based VLAN, up to 256 VLAN groups
    802.1ad Q-in-Q (VLAN stacking)
    GVRP for VLAN management
    Private VLAN Edge (PVE) supported
    Protocol-based VLAN
    MAC-based VLAN
    IP subnet VLAN
    Bandwidth Control TX/RX/both
    Link Aggregation IEEE 802.3ad LACP/static trunk
    Supports 128 groups with 8 ports per trunk group
    QoS 8 priority queues on all switch ports
    Supports strict priority and Weighted Round Robin (WRR) CoS policies
    Traffic classification:
    – IEEE 802.1p CoS/ToS
    – IPv4/IPv6 DSCP
    – Port-based WRR
    Multicast IGMP v1/v2/v3 snooping
    Querier mode support
    MLD v1/v2 snooping
    Querier mode support
    Multicast VLAN Register (MVR)
    Access Control List Supports Standard and Expanded ACL
    IP-based ACL/MAC-based ACL
    Time-based ACL
    Up to 512 entries
    Bandwidth Control At least 64Kbps step
    Security Supports MAC + port binding
    IPv4/IPv6 + MAC + port binding
    IPv4/IPv6 + port binding
    Supports MAC filter
    ARP scanning prevention
    Authentication IEEE 802.1x port-based network access control
    AAA authentication: TACACS+ and IPv4/IPv6 over RADIUS
    SNMP MIBs RFC 1213 MIB-II
    RFC 1215 Internet Engineering Task Force
    RFC 1271 RMON
    RFC 1354 IP-Forwarding MIB
    RFC 1493 Bridge MIB
    RFC 1643 Ether-like MIB
    RFC 1907 SNMP v2
    RFC 2011 IP/ICMP MIB
    RFC 2012 TCP MIB
    RFC 2013 UDP MIB
    RFC 2096 IP forward MIB
    RFC 2233 if MIB
    RFC 2452 TCP6 MIB
    RFC 2454 UDP6 MIB
    RFC 2465 IPv6 MIB
    RFC 2466 ICMP6 MIB
    RFC 2573 SNMP v3 notify
    RFC 2574 SNMP v3 vacm
    RFC 2674 Bridge MIB Extensions
    Standard Conformance
    Regulatory Compliance FCC Part 15 Class A, CE
    Standards Compliance IEEE 802.3 10BASE-T
    IEEE 802.3u 100BASE-TX
    IEEE 802.3z Gigabit 1000BASE-SX/LX
    IEEE 802.3ab Gigabit 1000BASE-T
    IEEE 802.3x flow control and back pressure
    IEEE 802.3ad port trunk with LACP
    IEEE 802.1D Spanning Tree Protocol
    IEEE 802.1w Rapid Spanning Tree Protocol
    IEEE 802.1s Multiple Spanning Tree Protocol
    IEEE 802.1p Class of Service
    IEEE 802.1Q VLAN tagging
    IEEE 802.1X port authentication network control
    IEEE 802.1ab LLDP
    IEEE 802.3af Power over Ethernet
    IEEE 802.3at Power over Ethernet PLUS
    RFC 768 UDP
    RFC 793 TFTP
    RFC 791 IP
    RFC 792 ICMP
    RFC 2068 HTTP
    RFC 1112 IGMP v1
    RFC 2236 IGMP v2
    RFC 3376 IGMP v3
    RFC 2710 MLD v1
    FRC 3810 MLD v2
    RFC 2328 OSPF v2
    RFC 1058 RIP v1
    RFC 2453 RIP v2
    Environment
    Operating Temperature: 0 ~ 50 degrees C
    Relative Humidity: 5 ~ 90% (non-condensing)
    Storage Temperature: -10 ~ 70 degrees C
    Relative Humidity: 5 ~ 90% (non-condensing)
    Ordering Information
    SGS-6340-24P4S Layer 3 24-Port 10/100/1000T 802.3at PoE + 4-Port 1000X SFP Stackable Managed Switch (370W)

Facebooktwittergoogle_pluspinterestlinkedinyoutube

SGS-6340-20S4C4X

box_SGS-6340-20S4C4X
SGS-6340-20S4C4X
Layer 3 20-Port 100/1000X SFP + 4-Port Gigabit TP/SFP + 4-Port 10G SFP+ Stackable Managed Switch
3icon_L3_RIP_Routing 4icon_L3_OSPF_Routing 4icon_SSL-SSH 0icon_snmp 1icon_IPv6-Management 3icon_10Gbps_SFP+

  • Powerful Solution for All Long-Reach Networks
    PLANET SGS-6340-20S4C4X is a Layer 3 Stackable Managed Gigabit Switch that provides high-density performance by its Layer 3 Gigabit static routing with 10Gbps uplink and multiple SFP fiber interfaces delivered in a rugged strong case. The administrator can flexibly choose the suitable SFP/SFP+ transceiver according to the transmission distance or the transmission speed required to extend the 10G network efficiently. Besides, with 128Gbps switching fabric, the SGS-6340-20S4C4X can handle extremely large amounts of data in a secure topology linking to backbone or high capacity servers for ISP and enterprise VoIP, video streaming, and multicast applications.
    AC and DC Redundant Power to Ensure Continuous Operation
    The SGS-6340-20S4C4X is equipped with one 100~240V AC power supply unit and one additional -48 ~ -60V DC power supply unit for redundant power supply installation. A redundant power system is also provided to enhance the reliability with either AC or DC power supply unit. The redundant power system is specifically designed to handle the demands of high-tech facilities requiring the highest power integrity. Furthermore, with the -48 ~ -60V DC power supply implemented, the SGS-6340-20S4C4X can be applied as the telecom level device.Layer 3 Routing Support
    The SGS-6340-20S4C4X enables the administrator to conveniently boost network efficiency by configuring Layer 3 static routing manually, the RIP (Routing Information Protocol) or OSPF (Open Shortest Path First) settings automatically. The RIP can employ the hop count as a routing metric and prevent routing loops by implementing a limit on the number of hops allowed in a path from the source to a destination. The maximum number of hops allowed for the RIP is 15. The OSPF is an interior dynamic routing protocol for autonomous system based on link-state. The protocol creates a link-state database by exchanging link-states among Layer3 switches, and then uses the Shortest Path First algorithm to generate a route table based on that database.
    High Performance
    The SGS-6340-20S4C4X boasts a high-performance switch architecture that is capable of providing non-blocking switch fabric and wire-speed throughput as high as 56Gbps, which greatly simplifies the tasks of upgrading the LAN for catering to increasing bandwidth demands.Abundant IPv6 Support
    The SGS-6340-20S4C4X provides IPv6 management and enterprise-level secure features such as SSH, ACL,WRR (Weighted Round Robin) and RADIUS authentication. The SGS-6340-20S4C4X thus helps the enterprises to step in the IPv6 era with the lowest investment. In addition, you don’t need to replace the network facilities when the IPv6 FTTx edge network is built.

    Excellent and Secure Traffic Control
    The SGS-6340-20S4C4X is loaded with powerful traffic management and WRR features to enhance services offered by telecoms and enterprises. The WRR functionalities include wire-speed Layer 4 traffic classifiers and bandwidth limitation which are particularly useful for multi-tenant unit, multi-business unit, Telco, or network service applications. The ACL policies supported can classify the traffic by source/destination IP addresses, source/destination MAC addresses, IP protocols, TCP/UDP, IP precedence, time ranges and ToS. Moreover, various policies can be conducted to forward the traffic. The SGS-6340-20S4C4X also provides IEEE 802.1x port based access authentication, which can be deployed with RADIUS, to ensure the port level security and block illegal users. Thus, the SGS-6340-20S4C4X empowers ISP and enterprises to take full advantage of the limited network resources and guarantees the best performance in VoIP and video conferencing transmission.

    Robust Layer 2 Features
    The SGS-6340-20S4C4X can be programmed for basic switch management functions such as port speed configuration, port aggregation, VLAN, Spanning Tree Protocol, WRR, bandwidth control and IGMP snooping. It also supports 802.1Q tagged VLAN, Q-in-Q, voice VLAN and GVRP Protocol. The VLAN groups allowed to be on the SGS-6340-20S4C4X will be maximally up to 256. By supporting port aggregation, the SGS-6340-20S4C4X allows the operation of a high-speed trunk combined with multiple ports. It enables up to 128 groups for trunking with a maximum of 8 ports for each group.Efficient Management
    The SGS-6340-20S4C4X supports IP stacking function that helps network managers to easily configure up to 24 switches in the same series via one single IP address instead of connecting and setting each unit one by one. For efficient management, the SGS-6340-20S4C4X Managed Gigabit Switch is equipped with console, Web and SNMP management interfaces. With its built-in Web-based management interface, the SGS-6340-20S4C4X offers an easy-to-use, platform-independent management and configuration facility. The SGS-6340-20S4C4X supports standard Simple Network Management Protocol (SNMP) and can be managed via any standard-based management software. For text-based management, the SGS-6340-20S4C4X can be accessed via Telnet and the console port. Moreover, the SGS-6340-20S4C4X offers secure remote management by supporting SSH connection which encrypts the packet content at each session.

    Flexibility and Extension Solution
    The SGS-6340-20S4C4X provides twenty-four 100/1000Mbps dual speed SFP Fiber ports, four 1/10Gbps SFP+ Fiber ports, and four 10/100/1000Mbps TP/SFP combo ports. Each of the SFP+ slots supports Dual-Speed,10GBASE-SR/LR or 1000BASE-SX/LX. Therefore, the administrator can flexibly choose the suitable SFP transceiver according to not only the transmission distance, but also the transmission speed required. The distance can be extended from 550 meters to 2km (multi-mode fiber) or up to 10/20/30/40/50/70/120 km (single-mode fiber or WDM fiber). They are well suited for applications within the enterprise data centers and distributions.

    Ordering Information
    SGS-6340-20S4C4X Layer 3 20-Port 100/1000X SFP + 4-Port Gigabit TP/SFP + 4-Port 10G SFP+ Stackable Managed Switch


  • High Availability Mesh Networking Solution for Big Data System
    By means of improving the technology of Optical Fiber Ethernet with highly-flexible, highly-extendable and easy-to-install features, the SGS-6340-20S4C4X offers up to 128Gbps data exchange speed via Optical Fiber interface and the transmission distance can be extended to 10km. The SGS-6340-20S4C4X features strong rapid self-recovery capability to prevent interruptions and external intrusions. It incorporates Multiple Spanning Tree Protocol (802.1s MSTP) into customer’s automation network to enhance system reliability and uptime. The SGS-6340-20S4C4X is the ideal solution for data centers, service providers and telecoms to build redundant connection and establish high bandwidth for Big Data server farm.
    Triple Play Service of Backbone Network Solution
    In telecommunications, triple play service is a marketing term for the provisioning, over a single broadband connection of more bandwidth-intensive services, such as broadband Internet access, television and the latency-sensitive telephone. The SGS-6340-20S4C4X provides up to 128Gbps bandwidth to exchange data, voice and video packets via fiber patch cable. It’s the suitable aggregation switch for ISPs and Telcos building a heavy traffic backbone network infrastructure.
    Layer 3 VLAN Routing and 10G Uplink Application
    With the built-in robust Layer 3 routing protocols, the SGS-6340-20S4C4X ensures reliable routing between VLANs and network segments. The routing protocols can be applied by VLAN interface with up to 128 routing entries. The SGS-6340-20S4C4X, certainly an ideal solution for enterprises, offers greater security, control and bandwidth conservation, and high-speed uplink.
    Ordering Information
    SGS-6340-20S4C4X Layer 3 20-Port 100/1000X SFP + 4-Port Gigabit TP/SFP + 4-Port 10G SFP+ Stackable Managed Switch


  • Hardware Specifications
    Copper Ports 4 10/100/1000BASE-T RJ45 auto-MDI/MDI-X ports, shared with port-21 to port-24
    SFP/mini-GBIC Slots 24 100/1000BASE-X SFP interfaces
    Compatible with 100BASE-FX SFP transceiver
    SFP+ Slots 4 10GBASE-SR/LR SFP+ interface (port-25 to port-28)
    Compatible with 1000BASE-SX/LX/BX SFP transceiver
    Console 1 x RJ45-to-RS232 serial port (9600, 8, N, 1)
    Switch Architecture Store-and-forward
    Switch Fabric 128Gbps/non-blocking
    Switch Throughput 95.24Mpps
    Address Table 16K MAC address table with auto learning function
    Shared Data Buffer 1.5MB
    Flow Control Back pressure for half-duplex
    IEEE 802.3x pause frame for full-duplex
    Jumbo Frame 9KB
    LED System:
    PWR, SYS
    Ports:
    10/100/1000T RJ45 Port: LNK/ACT
    100/1000X SFP Slot: LNK/ACT
    1/10G SFP+ Slot: LNK/ACT
    Dimensions (W x D x H) 442 x 220 x 44 mm, 1U height
    Weight 2821g
    Power Consumption 54.5 watts/185.96 BTU (maximum)
    Power Requirements AC 100~240V, 50/60Hz
    DC -48 ~ -60V
    Fan 2
    Management Function
    System Configuration Console, Telnet, SSH, Web browser, SNMP v1, v2c and v3
    Management Supports both IPv4 and IPv6 addressing
    Supports the user IP security inspection for IPv4/IPv6 SNMP
    Supports MIB and TRAP
    Supports IPv4/IPv6 FTP/TFTP
    Supports IPv4/IPv6 NTP
    Supports RMON 1, 2, 3, 9 four groups
    Supports the RADIUS authentication for IPv4/IPv6 Telnet user name and password
    Supports IPv4/IPv6 SSH
    The right configuration for users to adopt RADIUS server’s shell management
    Supports CLI, console, Telnet
    Supports SNMPv1, v2c and v3
    Supports Security IP safety net management function: avoid unlawful landing at non-restrictive area
    Supports Syslog server for IPv4 and IPv6
    Supports TACACS+
    Layer 3 Function
    Routing Protocol Static routing, RIP and OSPF
    Routing Table 128
    Layer 2 Function
    Port Configuration Port disable/enable
    Auto-negotiation 10/100/1000Mbps full and half duplex mode selection
    Flow control disable/enable
    Bandwidth control on each port
    Port loopback detect
    Port Status Display each port’s speed duplex mode, link status, flow control status and
    auto negotiation status
    VLAN 802.1Q tagged based VLAN, up to 256 VLAN groups
    802.1ad Q-in-Q (VLAN stacking)
    GVRP for VLAN management
    Private VLAN Edge (PVE) supported
    Protocol-based VLAN
    MAC-based VLAN
    IP subnet VLAN
    Bandwidth Control TX/RX/both
    Link Aggregation IEEE 802.3ad LACP/static trunk
    Supports 128 groups with 8 ports per trunk group
    QoS 8 priority queues on all switch ports
    Supports strict priority and Weighted Round Robin (WRR) CoS policies
    Traffic classification:
    – IEEE 802.1p CoS/ToS
    – IPv4/IPv6 DSCP
    – Port-based WRR
    Multicast IGMP v1/v2/v3 snooping
    Querier mode support
    MLD v1/v2 snooping
    Querier mode support
    Multicast VLAN Register (MVR)
    Access Control List Supports Standard and Expanded ACL
    IP-based ACL/MAC-based ACL
    Time-based ACL
    Up to 512 entries
    Bandwidth Control At least 64Kbps stream
    Security Supports MAC + port binding
    IPv4/IPv6 + MAC + port binding
    IPv4/IPv6 + port binding
    Supports MAC filter
    ARP scanning prevention
    Authentication IEEE 802.1x port-based network access control
    AAA authentication: TACACS+ and IPv4/IPv6 over RADIUS
    SNMP MIBs RFC 1213 MIB-II
    RFC 1215 Internet Engineering Task Force
    RFC 1271 RMON
    RFC 1354 IP-Forwarding MIB
    RFC 1493 Bridge MIB
    RFC 1643 Ether-like MIB
    RFC 1907 SNMPv2
    RFC 2011 IP/ICMP MIB
    RFC 2012 TCP MIB
    RFC 2013 UDP MIB
    RFC 2096 IP forward MIB
    RFC 2233 if MIB
    RFC 2452 TCP6 MIB
    RFC 2454 UDP6 MIB
    RFC 2465 IPv6 MIB
    RFC 2466 ICMP6 MIB
    RFC 2573 SNMPv3 notification
    RFC 2574 SNMPv3 VACM
    RFC 2674 Bridge MIB Extensions
    Standard Conformance
    Regulatory Compliance FCC Part 15 Class A, CE
    Standards Compliance IEEE 802.3 10BASE-T
    IEEE 802.3u 100BASE-TX
    IEEE 802.3z Gigabit 1000BASE-SX/LX
    IEEE 802.3ab Gigabit 1000BASE-T
    IEEE 802.3ae 10Gb/s Ethernet
    IEEE 802.3x flow control and back pressure
    IEEE 802.3ad port trunk with LACP
    IEEE 802.1D Spanning Tree Protocol
    IEEE 802.1w Rapid Spanning Tree Protocol
    IEEE 802.1s Multiple Spanning Tree Protocol
    IEEE 802.1p Class of Service
    IEEE 802.1Q VLAN tagging
    IEEE 802.1X port authentication network control
    IEEE 802.1ab LLDP
    RFC 768 UDP
    RFC 793 TFTP
    RFC 791 IP
    RFC 792 ICMP
    RFC 2068 HTTP
    RFC 1112 IGMP v1
    RFC 2236 IGMP v2
    RFC 3376 IGMP v3
    RFC 2710 MLD v1
    FRC 3810 MLD v2
    RFC 2328 OSPF v2
    RFC 1058 RIP v1
    RFC 2453 RIP v2
    Environment
    Operating Temperature: 0 ~ 50 degrees C
    Relative Humidity: 5 ~ 90% (non-condensing)
    Storage Temperature: -10 ~ 70 degrees C
    Relative Humidity: 5 ~ 90% (non-condensing)
    Ordering Information
    SGS-6340-20S4C4X Layer 3 20-Port 100/1000X SFP + 4-Port Gigabit TP/SFP + 4-Port 10G SFP+ Stackable Managed Switch

Facebooktwittergoogle_pluspinterestlinkedinyoutube

XGS3-24242

box_XGS3-24242
XGS3-24242
24-Port 100/1000X SFP Stackable Layer 3 Managed Switch with 4 Optional 10G Slots
0icon_IPv6IPv4_Routing 1icon_IPv6IPv4_Tunneling 6icon_10Gbps 4icon_SSL-SSH 0icon_snmp 2icon_IPv6IPv4_ACLQoS
  • IPv6 Routing and 10G Ethernet Switch Solutions for the Next Generation Internet Protocol
    IPv6 (Internet Protocol version 6) is well known as the next generation Internet Protocol to solve the lack of available IPv4 addresses. IPv6 can provide larger address space than IPv4 for the rapid growing networks. To provide smooth migration path from IPv4 to IPv6 for the future network upgrades, PLANET releases the multi-layer IPv6 / IPv4 Gigabit Ethernet Routing Switch, XGS3-24242, to meet the bandwidth requirements and protect network investment for enterprises. The XGS3-24242 is implemented with the following advanced technologies: 

     

        • IPv6 / IPv4 Routing and Management
     • 10G Ethernet Switching
     • Single IP Address Management
     • Redundant Power SystemThe XGS3-24242 provides 24 shared 100/1000Base-X SFP slots with 12 shared 10/100/1000Mbps copper ports, two optional 2-Port 10Gbps SFP+ uplink module slots in a compact 1U height format. Positioned as the distribution or aggregation layer switch of large networks, the XGS3-24242 supports IP Stacking technology that helps to manage and configure up to 24 units via one single IP address easily. It serves for campus networks and metropolitan IP networks by offering intelligent security features, high performance and flexibility. The XGS3-24242 can also be an excellent choice as a core layer switch for enterprises, data centers or small and medium-sized networks.

     

    Multi Port Fiber Optical Connective Capability Extends the Coverage of Multi-Layer Routing Services
    The XGS3-24242 Multi-layer Switch is an essential Layer 3 multimedia switch, which brings high-end security and traffic control to the edge of the network. The XGS3-24242 offers multi port fiber optical connective capability and helps to extend the coverage of multi-layer routing services. With IP routing and multicast routing capabilities and flexible SFP interfaces, the XGS3-24242 is the ideal choice for the core layer of telecoms, campuses, and enterprises that need long reach and stability of IP metro access networks.

     

    Supporting 10Gb Ethernet
    10Gb Ethernet, which adopts full-duplex technology instead of low-speed, half-duplex CSMA/CD protocol, is a big leap in the evolution of Ethernet. 10Gb Ethernet can be deployed in a star or ring topology. With 10Gb Ethernet technology applied, the XGS3-24242 provides broad bandwidth and powerful processing capacity. It is suitable for metropolitan networks and wide area networks. Using the XGS3-24242, users can simplify network structures and reduce cost of network construction.

     

    Networking Protocols
    The XGS3-24242 supports various networking protocols to meet the requirements of complex network constructions. It is compatible with 802.1D/w/s, 802.1Q, 802.1p, 802.3ad, 802.3x, GVRP, DHCP, SNTP, etc. The Switch also supports multicast protocols including IGMP, DVMRP and PIM. Moreover, the XGS3-24242 complies with RIPv1/2, OSPF and IPv6.

     

    Reliable Power Supply
    The XGS3-24242 provides AC/DC power redundancy. It can be deployed with 100~240V AC power input, -48V DC power input or 100~240V AC power/-48V DC power input simultaneously.

     

    ACL
    The XGS3-24242 supports ACL policies comprehensively. The traffic can be classified by source/destination IP addresses, source/destination MAC addresses, IP protocols, TCP/UDP, IP precedence, time ranges and ToS. Moreover, various policies can be conducted to forward the traffic. The XGS3-24242 also provides IEEE 802.1x port based access authentication, which can be deployed with RADIUS, to ensure the port level security and block illegal users.

     

    QoS
    The XGS3-24242 switch fully supports DiffServ module. Users can specify a queue bandwidth on each port. WRR/SP/SWRR scheduling is also provided. The XGS3-24242 supports the port security to enable users to deploy trusted CoS, DSCP, IP precedence and port priority. Users can modify packets’ DSCP and COS values so the traffic can be classified by port, VLAN, DSCP, IP precedence and ACL table. User can also modify packets’ DSCP and IP precedence values to specify different bandwidths for voice / data / video to customize different qualities of service.

     

    Perfect Web Management
    The XGS3-24242 supports SNMP, In-band and Out-of-band Management, CLI and WEB interface, and RMON. It can mail the correlative sensitive information to the administrator abide by SMTP protocol. The XGS3-24242 supports SSH protocol to ensure the configuration management security of the switch.

    Ordering Information
    XGS3-24242 24-Port Stackable Gigabit Layer 3 Managed Switch with 4 Optional 10G slots
    Accessories
    XGS3-2SFP+ 2-Port 10G SFP+ Optic Module for XGS3-24242
    MTB-LR SFP+ Port 10GBase-LR Mini-GBIC module (Single mode / 1310nm / max. 10km)
    MTB-SR SFP+ Port 10GBase-SR Mini-GBIC Module (Multi-mode / 850nm / max. 300m)


  • Core Routing Switch
    With 24 SFP fiber interfaces with 12 shared Gigabit ports and Layer 3 IP / multicast routing capability, the XGS3-24242 provides a cost-effective and high-performance solution for telecoms, network service providers and enterprises.
     

    Campus / ISP / Telecom High density and VRRP Backbone Routing Switch
    With the built-in robust IPv4 / IPv6 Layer 3 IP and multicast routing protocols, the XGS3-24242 ensures reliable routing between VLANs and network segments. The routing protocols can be applied by VLAN interface with up to 1K routing entries. The high-density routing interfaces provide expandability to meet the growing network’s needs. Moreover, with the hot VLAN feature – Q-in-Q (VLAN stacking) supported, it allows the service providers to offer certain services such as Internet access on specific VLANs for specific customers and yet still provides other types of services for their other customers on other VLANs.

     

    Data Center Security and QoS Switch
    The XGS3-24242 performs 128 Gigabits per second, non-blocking switch fabric so it can easily provide a local, high bandwidth, and Gigabit Ethernet network for backbone of your department. With the 24 built-in SFP ports, the XGS3-24242 provides the uplink to the backbone network through Gigabit Ethernet LX/SX SFP modules. It further improves the network efficiency and protects the network clients by offering the security and QoS features.

    Ordering Information
    XGS3-24242 24-Port Stackable Gigabit Layer 3 Managed Switch with 4 Optional 10G slots
    Accessories
    XGS3-2SFP+ 2-Port 10G SFP+ Optic Module for XGS3-24242
    MTB-LR SFP+ Port 10GBase-LR Mini-GBIC module (Single mode / 1310nm / max. 10km)
    MTB-SR SFP+ Port 10GBase-SR Mini-GBIC Module (Multi-mode / 850nm / max. 300m)

  • Hardware Specifications
    SFP/Mini-GBIC Slots 24 SFP slots, 100/1000Base-X SFP transceiver
    Copper Ports 12 10/100/1000Base-T RJ-45 auto-MDI/MDI-X ports compatible
    Shared with Port-13 to Port-24
    Expansion Slots 2 slots for PLANET XGS3-2SFP+, 2-Port 10G SFP+ optic module
    Supports module hot-swappable
    Switch Processing Scheme Store-and-Forward
    Switch Fabric 128Gbps
    Throughput 95Mpps@64bytes
    Address Table 16K entries
    Share Data Buffer 1.5Mbytes
    VLAN Table 4K
    ACL Table 1K
    Routing Table 13K
    Layer 3 Interface 1K
    Port Queues 8
    Flow Control IEEE 802.3x pause frame for full-duplex
    Back pressure for half-duplex
    Jumbo Frame 9Kbytes
    LED System:
    Power, SYS diagnostic, Redundant Power, Module, Stack
    Ports:
    10/100/1000 Link/Act
    Dimension (W x D x H) 415 x 325 x 44.5 mm, 1U height
    Weight 4.3kg
    Power Requirements AC: 100 ~ 240VAC, 50 / 60Hz, auto-sensing
    DC: -48V DC
    Power Consumption 79 watts max.
    IPv4 Layer 3 Functions
    IP Routing Protocol Static Route, RIPv1/v2, OSPFv2, BGPv4
    Policy-based Routing (PBR)
    LPM Routing (MD5 authentication)
    Multicast Routing Protocol IGMP v1 / v2 / v3, DVMRP, PIM-DM/SM, PIM-SSM
    Layer 3 Protocol VRRP v1/v3, ARP, ARP Proxy
    Routing Interface Per VLAN
    IPv6 Layer 3 Functions
    IP Routing Protocol RIPng, OSPFv3, BGPv4+
    Multicast Routing Protocol PIM-SM/DM for IPv6
    MLD for IPv6 (v1)
    MLDv1/v2
    MLD Snooping, 6 to 4 Tunnels
    Multicast receive control
    Illegal multicast source detect
    Layer 3 Protocol Configured Tunnels, ISATAP, CIDR
    Layer 2 Functions
    Port Configuration Port disable/enable
    Auto-negotiation 10/100/1000Mbps full and half duplex mode selection
    Bandwidth control on each port
    Port Loopback detect
    VLAN 802.1Q Tagged based VLAN, up to 4K VLAN groups
    Q-in-Q
    GVRP
    Private VLAN
    Voice VLAN
    MAC-based VLAN
    Protocol-based VLAN
    Spanning Tree Protocol STP, IEEE 802.1D (Spanning Tree Protocol)
    RSTP, IEEE 802.1w (Rapid Spanning Tree Protocol)
    MSTP, IEEE 802.1s (Multiple Spanning Tree Protocol, spanning tree by VLAN)
    Root Guard
    BPDU Guard
    Link Aggregation Static trunk
    IEEE 802.3ad LACP
    Supports 16 groups of 8-Port trunk
    QoS Traffic classification based, strict priority and WRR
    8-level priority for switching
    – Port number
    – 802.1p priority
    – DSCP/TOS field in IP Packet
    Policy-based DiffServ
    Multicast IGMP v1 / v2 / v3 snooping
    IGMP proxy
    IGMP Querier mode support
    MLD v1/v2, MLD v1/v2 Snooping
    Access Control List Support standard and expanded ACL
    IP-based ACL / MAC-Based ACL
    Time-Based ACL
    ACL Pool can be used for QoS classification
    Up to 4K entries
    Security Supports MAC+ port binding
    IPv4 / IPv6 + MAC+ port binding
    IPv4 / IPv6 + port binding
    Supports MAC filter
    ARP Spoofing Prevention
    ARP Scanning Prevention
    IP Source Guard
    Authentication IEEE 802.1x Port-based network access control
    AAA Authentication: IPv4 / IPv6 over RADIUS
    SNMP MIBs RFC-1213 MIB-II
    IF-MIB
    RFC-1493 Bridge MIB
    RFC-1643 Ethernet MIB
    RFC-2863 Interface MIB
    RFC-2665 Ether-Like MIB
    RFC-2674 Extended Bridge MIB
    RFC-2819 RMON MIB (Group 1, 2, 3 and 9)
    RFC-2737 Entity MIB
    RFC-2618 RADIUS Client MIB
    RFC-2933 IGMP-STD-MIB
    RFC-3411 SNMP-Frameworks-MIB
    IEEE 802.1X PAE
    LLDP
    MAU-MIB
    Management Functions
    System Configuration Console, Telnet, SSH, Web Browser, SSL, SNMPv1, v2c and v3
    Management Supports the unite for IPv4 / IPv6 HTTP and SSL
    Supports the user IP security inspection for IPv4 / IPv6 SNMP
    Supports MIB and TRAP
    Supports IPv4 / IPv6 FTP/TFTP
    Supports IPv4 / IPv6 NTP
    Supports RMOM 1, 2, 3, 9 four group
    Supports the RADIUS authentication for IPv4 / IPv6 telnet user name and password
    Supports IPv4 / IPv6 SSH
    The right configuration for users to adopt radius server’s shell management
    Supports the function for timing-reset bases needs
    Supports CLI, Console (RS-232), Telnet
    Supports SNMPv1 / v2c / v3
    Supports Security IP safety net management function:avoid unlawful landing at nonrestrictive area
    Supports TACACS+
    Standards Conformance
    Regulation Compliance FCC Part 15 Class A, CE
    Standards Compliance IEEE 802.3 10Base-T
    IEEE 802.3u 100Base-TX
    IEEE 802.3z Gigabit SX/LX
    IEEE 802.3ab Gigabit 1000Base-T
    IEEE 802.3ae 10 Gigabit Ethernet
    IEEE 802.3x Flow Control and Back Pressure
    IEEE 802.3ad Port Trunk with LACP
    IEEE 802.1d Spanning Tree Protocol
    IEEE 802.1w Rapid Spanning Tree Protocol
    IEEE 802.1s Multiple Spanning Tree Protocol
    IEEE 802.1p Class of Service
    IEEE 802.1Q VLAN Tagging
    IEEE 802.1x Port Authentication Network Control
    IEEE 802.1ab LLDP
    Environment
    Operating Temperature: 0 ~ 50 degrees C
    Relative Humidity: 5 ~ 90% (non-condensing)
    Storage Temperature: -10 ~ 70 degrees C
    Relative Humidity: 5 ~ 90% (non-condensing)
    Ordering Information
    XGS3-24242 24-Port Stackable Gigabit Layer 3 Managed Switch with 4 Optional 10G slots
    Accessories
    XGS3-2SFP+ 2-Port 10G SFP+ Optic Module for XGS3-24242
    MTB-LR SFP+ Port 10GBase-LR Mini-GBIC module (Single mode / 1310nm / max. 10km)
    MTB-SR SFP+ Port 10GBase-SR Mini-GBIC Module (Multi-mode / 850nm / max. 300m)

     

Facebooktwittergoogle_pluspinterestlinkedinyoutube

XGS3-24042

box_XGS3-24042
XGS3-24042
24-Port Stackable Gigabit Layer 3 Managed Switch with 4 Optional 10G slots
0icon_IPv6IPv4_Routing 1icon_IPv6IPv4_Tunneling 6icon_10Gbps 4icon_SSL-SSH 0icon_snmp 2icon_IPv6IPv4_ACLQoS
  • IPv6 Routing and 10G Ethernet Switch Solutions for the Next Generation Internet Protocol
    IPv6 (Internet Protocol version 6) is well known as the next generation Internet Protocol to solve the lack of available IPv4 addresses. IPv6 can provide larger address space than IPv4 for the rapid growing networks. To provide smooth migration path from IPv4 to IPv6 for the future network upgrades, PLANET releases the multi-layer IPv6 / IPv4 Gigabit Ethernet Routing Switch, XGS3-24042, to meet the bandwidth requirements and protect network investment for enterprises. The XGS3-24042 is implemented with the following advanced technologies:         • IPv6 / IPv4 Routing and Management
     • 10G Ethernet Switching
     • Single IP Address Management
     • Redundant Power SystemThe XGS3-24042 provides 24 fixed 10/100/1000Mbps copper ports with 4 shared 100/1000Base-X SFP slots, two optional 2-Port 10Gbps SFP+ uplink module slots in a compact 1U height format. Positioned as the distribution or aggregation layer switch for large networks, the XGS3-24042 supports IP Stacking technology that helps to manage and configure up to 24 units via one single IP address easily. It serves for campus networks and metropolitan IP networks by offering intelligent security features, high performance and flexibility. The XGS3-24042 can also be an excellent choice as a core layer switch for enterprises, data centers or small and medium-sized networks.
    Supporting 10Gb Ethernet
    10Gb Ethernet, which adopts full-duplex technology instead of low-speed, half-duplex CSMA/CD protocol, is a big leap in the evolution of Ethernet. 10Gb Ethernet can be deployed in a star or ring topology. With 10Gb Ethernet technology applied, the XGS3-24042 provides broad bandwidth and powerful processing capacity. It is suitable for metropolitan networks and wide area networks. Using the XGS3-24042 can help users simplify network structures and reduce cost of network construction.
    Networking Protocols
    The XGS3-24042 supports various networking protocols to meet the requirements of complex network constructions. It is compatible with 802.1D/w/s, 802.1Q, 802.1p, 802.3ad, 802.3x, GVRP, DHCP, SNTP, etc. The Switch also supports multicast protocols including IGMP, DVMRP and PIM. Moreover, the XGS3-24042 complies with RIPv1/2, OSPF and IPv6.Reliable Power Supply
    The XGS3-24042 provides AC/DC power redundancy. It can be deployed with 100~240V AC power input, -48V DC power input or 100~240V AC power/-48V DC power input simultaneously.

     

    ACL
    The XGS3-24042 supports ACL policies comprehensively. The traffic can be classified by source/destination IP addresses, source/destination MAC addresses, IP protocols, TCP/UDP, IP precedence, time ranges and ToS. Moreover, various policies can be conducted to forward the traffic. The XGS3-24042 also provides IEEE 802.1x port based access authentication, which can be deployed with RADIUS, to ensure the port level security and block illegal users.

     

    QoS
    The XGS3-24042 switch fully supports DiffServ module. Users can specify a queue bandwidth on each port. WRR/SP/SWRR scheduling is also provided. The XGS3-24042 supports the port security to enable users to deploy trusted CoS, DSCP, IP precedence and port priority. Users can modify packets’ DSCP and COS values so the traffic can be classified by port, VLAN, DSCP, IP precedence and ACL table. User can also modify packets’ DSCP and IP precedence values to specify different bandwidths for voice / data / video to customize different qualities of service.

     

    Perfect Web Management
    The XGS3-24042 supports SNMP, In-band and Out-of-band Management, CLI and WEB interface, and RMON. It can mail the correlative sensitive information to the administrator abide by SMTP protocol. The XGS3-24042 supports SSH protocol to ensure the configuration management security of the switch.

    Ordering Information
    XGS3-24042 24-Port Stackable Gigabit Layer 3 Managed Switch with 4 Optional 10G slots
    Accessories
    XGS3-2SFP+ 2-Port 10G SFP+ Optic Module for XGS3-24042
    MTB-LR SFP+ Port 10GBase-LR Mini-GBIC Module (Single mode / 1310nm / max. 10km)
    MTB-SR SFP+ Port 10GBase-SR Mini-GBIC Module (Multi-mode / 850nm / max. 300m)


  • Core Routing Switch
    With 24 Gigabit ports with 4 shared SFP fiber interfaces and Layer 3 IP / Multicast Routing capability, the XGS3-24042 provides a cost-effective and high-performance solution for telecoms, network service providers and enterprises.
    Campus / ISP / Telecom High density and VRRP Backbone Routing Switch
    With the built-in robust IPv4 / IPv6 Layer 3 IP and multicast routing protocols, the XGS3-24042 ensures reliable routing between VLANs and network segments. The routing protocols can be applied by VLAN interface with up to 1K routing entries. The high-density routing interfaces provide expandability to meet the growing network’s needs. Moreover, with the hot VLAN feature – Q-in-Q (VLAN stacking) supported, it allows the service providers to offer certain services such as Internet access on specific VLANs for specific customers and yet still provides other types of services for their other customers on other VLANs.
    Data Center Security and QoS Switch
    The XGS3-24042 performs 128 Gigabits per second, non-blocking switch fabric so it can easily provide a local, high bandwidth, and Gigabit Ethernet network for backbone of your department. With the four built-in SFP ports, the XGS3-24042 provides the uplink to the backbone network through Gigabit Ethernet LX/SX SFP modules. It further improves the network efficiency and protects the network clients by offering the security and QoS features.
    Ordering Information
    XGS3-24042 24-Port Stackable Gigabit Layer 3 Managed Switch with 4 Optional 10G slots
    Accessories
    XGS3-2SFP+ 2-Port 10G SFP+ Optic Module for XGS3-24042
    MTB-LR SFP+ Port 10GBase-LR Mini-GBIC Module (Single mode / 1310nm / max. 10km)
    MTB-SR SFP+ Port 10GBase-SR Mini-GBIC Module (Multi-mode / 850nm / max. 300m)

  • Hardware Specifications
    Copper Ports 24 10/100/1000Base-T RJ-45 auto-MDI/MDI-X ports
    SFP/Mini-GBIC Slots 4 SFP slots, 100/1000Base-X SFP transceiver compatible
    Shared with Port-21 to Port-24
    Expansion Slots 2 slots for PLANET XGS3-2SFP+, 2-port 10G SFP+ optic module
    Support module hot-swappable
    Switch Processing Scheme Store-and-Forward
    Switch Fabric 128Gbps
    Throughput 95Mpps@64bytes
    Address Table 16K entries
    Share Data Buffer 1.5Mbytes
    VLAN Table 4K
    ACL Table 1K
    Routing Table 13K
    Layer 3 Interface 1K
    Port Queues 8
    Flow Control IEEE 802.3x pause frame for full-duplex
    Back pressure for half-duplex
    Jumbo Frame 9Kbytes
    LED System:
    Power, SYS diagnostic, redundant power, module, stack
    Ports:
    10/100/1000 Link/Act
    Dimensions (W x D x H) 415 x 325 x 44.5 mm, 1U height
    Weight 4.3kg
    Power Requirements AC: 100 ~ 240VAC, 50 / 60Hz, auto-sensing
    DC: -48V DC
    Power Consumption 79 watts max.
    IPv4 Layer 3 Functions
    IP Routing Protocol Static Route, RIPv1/v2, OSPFv2, BGPv4
    Policy-based Routing (PBR)
    LPM Routing (MD5 authentication)
    Multicast Routing Protocol IGMP v1 / v2 / v3, DVMRP, PIM-DM/SM, PIM-SSM
    Layer 3 Protocol VRRP v1/v3, ARP, ARP Proxy
    Routing Interface Per VLAN
    IPv6 Layer 3 Functions
    IP Routing Protocol RIPng, OSPFv3, BGPv4+
    Multicast Routing Protocol PIM-SM/DM for IPv6
    MLD for IPv6 (v1)
    MLDv1/v2
    MLD Snooping, 6 to 4 Tunnels
    Multicast receive control
    Illegal multicast source detect
    Layer 3 Protocol Configured Tunnels, ISATAP, CIDR
    Layer 2 Functions
    Port Configuration Port disable/enable
    Auto-negotiation 10/100/1000Mbps full and half duplex mode selection
    Bandwidth control on each port
    Port Loopback detect
    VLAN 802.1Q Tagged Based VLAN, up to 4K VLAN groups
    Q-in-Q
    GVRP
    Private VLAN
    Voice VLAN
    MAC-based VLAN
    Protocol-based VLAN
    Spanning Tree Protocol STP, IEEE 802.1D (Spanning Tree Protocol)
    RSTP, IEEE 802.1w (Rapid Spanning Tree Protocol)
    MSTP, IEEE 802.1s (Multiple Spanning Tree Protocol, spanning tree by VLAN)
    Root Guard
    BPDU Guard
    Link Aggregation Static Trunk
    IEEE 802.3ad LACP
    Supports 16 groups of 8-port trunk
    QoS Traffic classification based, Strict priority and WRR
    8-level priority for switching
    – Port Number
    – 802.1p priority
    – DSCP/TOS field in IP Packet
    Policy-based DiffServ
    Multicast IGMP v1 / v2 / v3 snooping
    IGMP proxy
    IGMP Querier mode support
    MLD v1/v2, MLD v1/v2 snooping
    Access Control List Supportd Standard and Expanded ACL
    IP-based ACL / MAC-based ACL
    Time-based ACL
    ACL Pool can be used for QoS classification
    Up to 4K entries
    Security Supports MAC+ port binding
    IPv4 / IPv6 + MAC+ port binding
    IPv4 / IPv6 + port binding
    Support MAC filter
    ARP spoofing prevention
    ARP Scanning prevention
    IP source guard
    Authentication IEEE 802.1x Port-based network access control
    AAA Authentication: IPv4 / IPv6 over RADIUS
    SNMP MIBs RFC-1213 MIB-II
    IF-MIB
    RFC-1493 Bridge MIB
    RFC-1643 Ethernet MIB
    RFC-2863 Interface MIB
    RFC-2665 Ether-Like MIB
    RFC-2674 Extended Bridge MIB
    RFC-2819 RMON MIB (Group 1, 2, 3 and 9)
    RFC-2737 Entity MIB
    RFC-2618 RADIUS Client MIB
    RFC-2933 IGMP-STD-MIB
    RFC-3411 SNMP-Frameworks-MIB
    IEEE 802.1X PAE
    LLDP
    MAU-MIB
    Management Functions
    System Configuration Console, Telnet, SSH, Web Browser, SSL, SNMPv1, v2c and v3
    Management Supports the unit for IPv4 / IPv6 HTTP and SSL
    Supports the user IP security inspection for IPv4 / IPv6 SNMP
    Supports MIB and TRAP
    Supports IPv4 / IPv6 FTP/TFTP
    Supports IPv4 / IPv6 NTP
    Supports RMOM 1, 2, 3, 9 four group
    Supports the RADIUS authentication for IPv4 / IPv6 telnet user name and password
    Supports IPv4 / IPv6 SSH
    The right configuration for users to adopt radius server’s shell management
    Supports the function for timing-reset bases needs
    Supports CLI, Console (RS-232), Telnet
    Supports SNMPv1 / v2c / v3
    Supports Security IP safety net management function:avoid unlawful landing at nonrestrictive area
    Supports TACACS+
    Standards Conformance
    Regulation Compliance FCC Part 15 Class A, CE
    Standards Compliance IEEE 802.3 10Base-T
    IEEE 802.3u 100Base-TX
    IEEE 802.3z Gigabit SX/LX
    IEEE 802.3ab Gigabit 1000Base-T
    IEEE 802.3ae 10 Gigabit Ethernet
    IEEE 802.3x Flow Control and Back pressure
    IEEE 802.3ad Port trunk with LACP
    IEEE 802.1d Spanning Tree protocol
    IEEE 802.1w Rapid Spanning Tree Protocol
    IEEE 802.1s Multiple Spanning Tree Protocol
    IEEE 802.1p Class of Service
    IEEE 802.1Q VLAN Tagging
    IEEE 802.1x Port Authentication Network Control
    IEEE 802.1ab LLDP
    Environment
    Operating Temperature: 0 ~ 50 degrees C
    Relative Humidity: 5 ~ 90% (non-condensing)
    Storage Temperature: -10 ~ 70 degrees C
    Relative Humidity: 5 ~ 90% (non-condensing)
    Ordering Information
    XGS3-24042 24-Port Stackable Gigabit Layer 3 Managed Switch with 4 Optional 10G slots
    Accessories
    XGS3-2SFP+ 2-Port 10G SFP+ Optic Module for XGS3-24042
    MTB-LR SFP+ Port 10GBase-LR Mini-GBIC Module (Single mode / 1310nm / max. 10km)
    MTB-SR SFP+ Port 10GBase-SR Mini-GBIC Module (Multi-mode / 850nm / max. 300m)

     

Facebooktwittergoogle_pluspinterestlinkedinyoutube

XGS3-42000R

XGS3-42000R
4-Slot Layer 3 IPv6/IPv4 Routing Chassis Switch
  • PLANET XGS3-42000R Core-Layer Routing Switch is specially designed for large network applications such as enterprises, campuses, communities, ISPs and data center networks where flexible configuration, large capacity, high density, high reliability and advanced traffic management are required.The XGS3-42000R is a High-Density Chassis Ethernet Switch built with 4 module slots and redundant power supply. It provides great porting flexibility for network deployment by offering various and combinable management modules and standard interfaces. For instance, one management module can be collaborated with three standard modules, or two management modules work with two standard modules to perform mutually system backup. Within the 6U height, single chassis, the maximum configuration can be:
    168-Port 10/100/1000Base-T Copper
    156-Port 1000Base-SX/LX SFP Fiber Slots
    13-Port 10G XFP Fiber Slots Positioned as the core layer switch, the XGS3-42000R serves ideally for large- and medium-sized networks and IP metropolitan networks by supplying advanced intelligent and secure features and giving high performance and flexibility

    Supporting 10-Gigabit Ethernet
    10-Gigabit Ethernet which adopts full-duplex technology instead of low-speed, half-duplex CSMA/CD protocol, is a big leap in the evolution of Ethernet. 10-Gigabit Ethernet can be deployed in star or ring topology. With 10-Gigabit Ethernet technology applied, the XGS3-42000R provides broad bandwidth and powerful processing capacity. It is suitable for metropolitan networks and wide area networks. Using the XGS3-42000R, users can simplify network structures and reduce cost of network construction.

    Abundant IPv6 Support
    The XGS3-42000R Chassis Switch supports IPv6 routing in hardware for maximum performance. As more network devices are growing and the need for larger addressing and higher security becomes critical, the XGS3-42000R Chassis Switch is the right product to meet the requirement.

    Scalable Performance
    The XGS3-42000R delivers wire-speed Gigabit and 10-Gigabit Ethernet connectivity in a highly flexible and resilient modular platform. With high switching capacity, the XGS3-42000R Chassis Switch supports wire-speed L2/L3 forwarding and high routing performance for IPv4 and IPv6 protocols. The scalable and flexible modular architecture supports up to 376Gps forwarding performance in a single system. The XGS3-42000R is ideal for the core layer of campuses, enterprise networks and the aggregation layer of IP metropolitan networks.

    Rich Multi-Layer and Multicast Networking Protocols
    The XGS3-42000R supports various Layer 2 and management networking protocols to meet the requirements of complex network constructions. It is compatible with 802.1d/w/s, 802.1Q, 802.1p, 802.3ad, 802.3x, GVRP, DHCP, SNTP, etc.

    The Chassis Switch also supports IPv6 / IPv4 routing protocols including Layer 3 IP Static Routing, RIPv1/v2, OSPF, and VRRP protocols. Built in with abundant multicast features, the XGS3-42000R supports rich L2 multicast features such as IGMPv1/v2/v3, snooping and L3 multicast protocols — DVMRP, PIM-DM, PIM-SM and PIM-SSM. Offering the rich application experience, the product supports multicast VLAN registration, multicast receive control and illegal multicast source detect functions. The XGS3-42000R Chassis Switch solution performs a cost-effective solution for today with the ability to expand as network demands grow.

    Enhanced Security
    PLANET XGS3-42000R offers comprehensive Layer 2 to Layer 4 Access Control List (ACL) for enforcing security to the edge. It can be used to restrict network access by denying packets based on source and destination IP address, TCP / UDP ports or defined typical network applications. Its protection mechanism also comprises 802.1x port-based and MAC-based user and device authentication. With the private VLAN function, communication between edge ports can be prevented to ensure user privacy. The XGS3-42000R Net Security also provides DHCP Snooping, IP Source Guard and Dynamic ARP Inspection functions to prevent from IP snooping attack and discard ARP packets with invalid MAC address. The network administrators can now construct highly secured corporate networks with considerably less time and effort than before.

    Enhanced Quality of Service
    The XGS3-42000R switch fully supports DiffServ module, so users can specify a queue bandwidth on each port. WRR / SP / SWRR scheduling is also provided. The XGS3-42000R supports the port security to enable trusted CoS, DSCP, IP precedence and port priority. Users can modify packets’ DSCP and COS values so that the traffic can be classified by port, VLAN, DSCP, IP precedence and ACL table. User can also modify packets’ DSCP and IP precedence values to specify different bandwidths for voice / data / video to customize different qualities of service.

    Efficient and Secure Management
    For efficient management, the XGS3-42000R Chassis Switch is equipped with console, WEB and SNMP management interfaces. With the built-in Web-based management interface, the XGS3-42000R offers an easy-to-use, platform-independent management and configuration facility. The XGS3-42000R supports standard Simple Network Management Protocol (SNMP) and can be managed via any standard-based management software. For text-based management, the XGS3-42000R can be accessed via Telnet and the console port. Moreover, the XGS3-42000R offers secure remote management by supporting SSH, SSL and SNMPv3 connection which encrypt the packet content at each session.

      Ordering Information
    XGS3-42000R 4-Slot Layer 3 IPv6/IPv4 Routing Chassis Switch ( with one AC power supply)
    XGS3-M24GX Management Module for XGS3-42000R with 24-Port Gigabit (12-Port Combo) + 1-Port 10G XFP
    XGS3-S24G Standard Module for XGS3-42000R with 24-Port Gigabit (12-Port Combo)
    XGS3-S48G Standard Module for XGS3-42000R with 48-Port Gigabit copper
    XGS3-S48GF Standard Module for XGS3-42000R with 48-Port Gigabit SFP
    XGS3-S4XG Standard Module for XGS3-42000R with 4-Port 10G XFP
    XGS3-PWR-AC 400watt AC power supply for XGS3-42000R
      Accessories
    MTB-XLR XFP Port 10GBase-LR Fiber Optic Module (Single mode / 1310nm / max. 10km)
    MTB-XSR XFP Port 10GBase-SR Fiber Optic Module (Multi-mode / 850nm / max. 300m)

  • Reliable, High Performance, High-Density Enterprise Backbone Switch
    10-Gigabit Ethernet supported equipment has become the fundamental unit of enterprises and network servers.. PLANET XGS3-42000R is the cost-effective, high-density and high-bandwidth Chassis Switch, which meet today’s market requirements. Dedicated chassis architecture features built into the XGS3-42000R make all modules in the platform operate together as one much larger switch providing multiple high-performance 10-Gigabit Ethernet network for backbone of enterprises, campuses or telecoms. The redundant management modules and dual power supplies provide the XGS3-42000R with nonstop network service ability. Moreover, all modules are hot swappable.. They can be added or exchanged without interrupting the whole system operation. The XGS3-42000R Chassis Switch is ideal to be used as a server farm switch connecting servers and perfectly suited to networking environments requiring constant access to critical business applications.
    Carrier Class Backbone Switch for Campus and Community
    For small area network communications on the campus and community, PLANET XGS3-42000R Chassis Switch enables an affordable and scalable network deployment. It offers a high capacity chassis platform with high quality and reliability in 10/100/1000Base-T, 1000Base-SX/LX and 10GBase-SR/LR scalable solutions that integrate easily into any large network. The XGS3-42000R provides up to 188 high-density Gigabit Ethernet ports, in which up to 156 mini-GBIC / SFP ports are available for remote uplink connectivity in a single system and provide the uplink to the edge network through 1000Base-SX/LX SFP modules. The XGS3-42000R offers a comprehensive set of modules for complex network and gives network manager the flexibility to expand large area network when needed.
      Ordering Information
    XGS3-42000R 4-Slot Layer 3 IPv6/IPv4 Routing Chassis Switch ( with one AC power supply)
    XGS3-M24GX Management Module for XGS3-42000R with 24-Port Gigabit (12-Port Combo) + 1-Port 10G XFP
    XGS3-S24G Standard Module for XGS3-42000R with 24-Port Gigabit (12-Port Combo)
    XGS3-S48G Standard Module for XGS3-42000R with 48-Port Gigabit copper
    XGS3-S48GF Standard Module for XGS3-42000R with 48-Port Gigabit SFP
    XGS3-S4XG Standard Module for XGS3-42000R with 4-Port 10G XFP
    XGS3-PWR-AC 400watt AC power supply for XGS3-42000R
      Accessories
    MTB-XLR XFP Port 10GBase-LR Fiber Optic Module (Single mode / 1310nm / max. 10km)
    MTB-XSR XFP Port 10GBase-SR Fiber Optic Module (Multi-mode / 850nm / max. 300m)

  • Hardware and Performance
    • 4 open module slots design
    – 2 management modules with 2 standard modules
    – 1 management module with 3 standard modules
    • Up to 168-port Gigabit copper / 156-port Gigabit SFP / 13-port 10G XFP
    • Hot-swappable switching modules
    • Non-blocking wire-speed Layer 2 and Layer 3 switching
    • 1 RJ-45 serial console interface on management module for switch basic management and setupRedundant Power System
    • 100~240V AC dual power redundant
    – 1 default AC power supply
    – 1 additional open slot for optional power supply
    • Active redundant power failure protection
    • Backup of catastrophic power failure on one supply

    IP Stacking
    • IP stacking technology, connects with stack member via any Gigabit or 10G interface
    • Single IP address management, supports up to 24 units stacked together

    IP Routing Features
    • IP Routing protocol supports RIP v1/v2, OSPF v2, BGP4
    • Routing interface provides VLAN routing mode
    • Policy based routing(PBR) for IPv4 and IPv6
    • VRRP protocol for redundant routing deployment
    • Supports route redistribution

    Multicast Routing Features
    • Supports Multicast Routing Protocols:
    – PIM-DM (Protocol Independent Multicast – dense mode)
    – PIM-SM (Protocol Independent Multicast – sparse mode)
    – PIM-SSM (Protocol Independent Multicast – source-specific multicast mode)
    – DVMRP (Distance Vector Multicast Routing Protocol)
    • Supports IGMP v1/v2/v3

    Layer 2 Features
    • Supports auto-negotiation, auto-MDI/MDI-x and half-duplex / full-duplex modes for all 1000Base-T ports.
    • Prevents packet loss with back pressure (half-duplex) and IEEE 802.3x PAUSE frame flow control (full-du
    • Supports VLAN
    – IEEE 802.1Q Tagged VLAN
    – Up to 4K VLANs groups, out of 4041 VLAN IDs
    – Provider bridging (VLAN Q-in-Q) support (IEEE 802.1ad)
    – GVRP protocol for VLAN management
    – Private VLAN Edge (PVE)
    • Supports Spanning Tree Protocol
    • STP, IEEE 802.1D (Spanning Tree Protocol)
    – RSTP, IEEE 802.1w (Rapid Spanning Tree Protocol)
    – MSTP, IEEE 802.1s (Multiple Spanning Tree Protocol, spanning tree by VLAN)
    • Supports Link Aggregation
    – 802.3ad Link Aggregation Control Protocol (LACP)
    – Cisco ether-channel (Static Trunk)
    – Maximum 128 trunk groups per module, up to 8 ports per trunk group
    – Up to 16Gbps bandwidth (duplex mode)
    • Provide port mirror (many-to-1)
    • Port mirroring to monitor the incoming or outgoing traffic on a particular port

    Quality of Service
    • 8 priority queues on all switch ports
    • Supports strict priority and weighted round robin (WRR) CoS policies
    • Ingress shaper and egress rate limit per port bandwidth control
    • Traffic-policing policies based on application

    Multicast
    • Supports IGMP snooping v1, v2 and v3
    • Querier mode support

    Security
    • IEEE 802.1x Port-based network access authentication
    • MAC-based network access authentication
    • IP-based Access Control List (ACL)
    • MAC-based Access Control List
    • Static MAC

    Management
    • IPv4 / IPv6 Switch Management Interfaces
    – Console / Telnet Command Line Interface
    – Web switch management
    – SNMP v1, v2c, and v3 switch management
    – SSH (Secure Shell) / SSL secure access
    • Four RMON groups (history, statistics, alarms, and events)
    • IPv6 IP Address / NTP / DNS management
    • Built-in Trivial File Transfer Protocol (TFTP) client
    • BOOTP and DHCP for IP address assignment
    • DHCP / BootP Relay and Relay Option 82
    • DHCP Server
    • DNS-Proxy
    • Firmware upload/download via FTP / TFTP
    • SNTP (Simple Network Time Protocol)
    • LLDP (Link Layer Discovery Protocol)
    • User Privilege levels control

      Ordering Information
    XGS3-42000R 4-Slot Layer 3 IPv6/IPv4 Routing Chassis Switch ( with one AC power supply)
    XGS3-M24GX Management Module for XGS3-42000R with 24-Port Gigabit (12-Port Combo) + 1-Port 10G XFP
    XGS3-S24G Standard Module for XGS3-42000R with 24-Port Gigabit (12-Port Combo)
    XGS3-S48G Standard Module for XGS3-42000R with 48-Port Gigabit copper
    XGS3-S48GF Standard Module for XGS3-42000R with 48-Port Gigabit SFP
    XGS3-S4XG Standard Module for XGS3-42000R with 4-Port 10G XFP
    XGS3-PWR-AC 400watt AC power supply for XGS3-42000R
      Accessories
    MTB-XLR XFP Port 10GBase-LR Fiber Optic Module (Single mode / 1310nm / max. 10km)
    MTB-XSR XFP Port 10GBase-SR Fiber Optic Module (Multi-mode / 850nm / max. 300m)

  •   Chassis Slots
    Total Number of Slots 4 ( 2 management modules + 2 standard modules
    or 1 managed module + 3 standard modules)
    Max. Management Module 2 (slot 1, slot 2)
    Max. Standard Module 3 (slot 2,3,4)
    Management Module Redundancy Yes
    Number of Power Supply Bays 2
    Number of Fan Trays 1, hot-pluggable
      Total Port Capacity
    Max. 10G XFP Slot 13
    Max. 10/100/1000Base-T 168
    Max. 1000Base-SX/LX SFP Slot 156
      Modules
    XGS3-M24GX Management module / 24 10/100/1000Base-T with 12 shared SFP slots + 1 10G XFP slot
    XGS3-S24G Standard module / 24 10/100/1000Base-T with 12 shared SFP slots
    XGS3-S48G Standard module / 48 10/100/1000Base-T
    XGS3-S48GF Standard module / 48 1000Base-SX/SL SFP slots
    XGS3-S4XG Standard module / 4 10GBase-SR/LR XFP slots
      Performance
    Switch Processing Scheme Store-and-Forward
    Backplane Bandwidth 1.2Tbps
    Switching Capacity 336Gbps
    Full-Mesh Switching Capacity 160Gbps
    Forwarding Rate 264Mpps@64bytes, line speed
    MAC Table 64K
    VLAN Table 4K
    ACL Table 16K max.
    Routing Table IPv4 protocol: 128K max.
    IPv6 protocol: 64K max.
    Layer 3 Interface 500 max.
    Port Queues 8
    Flow Control IEEE 802.3x pause frame for full-duplex
    Back pressure for half-duplex
    Jumbo Frame 9Kbytes
      Hardware Specification
    Dimensions (W x D x H) 445 x 421 x 266 mm
    Relative Humidity 10~90%, non-condensing
    Operating Temperature 0 ~ 50 degrees C
    Power Input AC: Input 100~240V, 50~60 Hz
    Power Consumption ≤400W
      IPv4 Layer 3 Functions
    IP Routing Protocol Static Route, RIPv1/v2, OSPFv2, BGP4
    Policy-based Routing (PBR)
    LPM Routing (MD5 authentication)
    Multicast Routing Protocol IGMP v1 / 2 / 3, DVMRP, PIM-DM/SM, PIM-SSM
    IPv4 Layer 3 Protocol VRRP, ARP, ARP proxy
    Routing Interface Per VLAN
      IPv6 Layer 3 Functions
    IP Routing Protocol RIPng, OSPFv3, BGP4+
    Multicast Routing Protocol PIM-SM/DM for IPv6
    MLD for IPv6
    MLDv1/v2
    MLD snooping, 6 to 4 tunnels
    Multicast receive control
    Illegal multicast source detect
    IPv6 Layer 3 Protocol Configured tunnels , ISATAP, CIDR
      Layer 2 Functions
    Port Configuration Port disable/enable
    Auto-negotiation 10/100/1000Mbps full and half duplex mode selection
    Bandwidth control on each port
    Port Loopback detect
    VLAN 802.1Q tagged based VLAN ,up to 4K VLAN groups
    Q-in-Q
    GVRP
    Private VLAN
    Spanning Tree Protocol STP, IEEE 802.1D (Spanning Tree Protocol)
    RSTP, IEEE 802.1w (Rapid Spanning Tree Protocol)
    MSTP, IEEE 802.1s (Multiple Spanning Tree Protocol, Spanning Tree by VLAN)
    Root Guard
    BPDU Guard
    Link Aggregation Static trunk
    IEEE 802.3ad LACP
    128 groups of 8-port trunk support
    QoS Traffic classification based, strict priority and WRR
    8-level priority for switching
    – Port number
    – 802.1p priority
    – DSCP / TOS field in IP Packet
    Policy-based DiffServ
    Multicast IGMP v1 / v2 / v3 Snooping
    IGMP Proxy
    IGMP querier mode support
    MLDv1 / v2, MLD v1/v2 snooping
    Access Control List Supports standard and expanded ACL
    IP-based ACL / MAC-based ACL
    Time-based ACL
    ACL pool can be used for QoS classification
    Up to 1K entries
    Security Supports MAC+ port binding
    IPv4 / IPv6 + MAC+ port binding
    IPv4 / IPv6 + port binding
    Supports MAC filter
    ARP spoofing prevention
    ARP scanning prevention
    IP source guard
    Authentication IEEE 802.1x Port-based network access control
    AAA Authentication: IPv4 / IPv6 over RADIUS
    SNMP MIBs RFC-1213 MIB-II
    IF-MIB
    RFC-1493 Bridge MIB
    RFC-1643 Ethernet MIB
    RFC-2863 Interface MIB
    RFC-2665 Ether-Like MIB
    RFC-2674 Extended Bridge MIB
    RFC-2819 RMON MIB (Group 1, 2, 3 and 9)
    RFC-2737 Entity MIB
    RFC-2618 RADIUS Client MIB
    RFC-2933 IGMP-STD-MIB
    RFC3411 SNMP-Frameworks-MIB
    IEEE802.1X PAE
    LLDP
    MAU-MIB
      Management Functions
    System Configuration Console, Telnet, SSH, Web Browser, SSL, SNMPv1, v2c and v3
    Management Interface IPv4 / IPv6 HTTP, SSL, SNMP, FTP/TFTP, NTP, SSH
    Telnet, CLI
    RADIUS, TACACS+
    RMOM 1,2,3,9 for group
    SNMP MTB and trap
      Standards Conformance
    Regulation Compliance FCC Part 15 Class A, CE
    Standards Compliance IEEE 802.3 10Base-T
    IEEE 802.3u 100Base-TX
    IEEE 802.3z 1000Base-SX/LX
    IEEE 802.3ab Gigabit 1000T
    IEEE 802.3ae 10 Gigabit Ethernet
    IEEE 802.3x Flow Control and Back pressure
    IEEE 802.3ad Port Trunk with LACP
    IEEE 802.1d Spanning Tree protocol
    IEEE 802.1w Rapid Spanning Tree Protocol
    IEEE 802.1s Multiple Spanning Tree Protocol
    IEEE 802.1p Class of service
    IEEE 802.1Q VLAN tagging
    IEEE 802.1x Port Authentication Network Control
    IEEE 802.1ab LLDP
      Environment
    Operating Temperature: 0 ~ 50 degrees C
    Relative Humidity: 10 ~ 90% (non-condensing)
    Storage Temperature: -10 ~ 70 degres C
    Relative Humidity: 5 ~ 90% (non-condensing)
       Ordering Information
    XGS3-42000R 4-Slot Layer 3 IPv6/IPv4 Routing Chassis Switch ( with one AC power supply)
    XGS3-M24GX Management Module for XGS3-42000R with 24-Port Gigabit (12-Port Combo) + 1-Port 10G XFP
    XGS3-S24G Standard Module for XGS3-42000R with 24-Port Gigabit (12-Port Combo)
    XGS3-S48G Standard Module for XGS3-42000R with 48-Port Gigabit copper
    XGS3-S48GF Standard Module for XGS3-42000R with 48-Port Gigabit SFP
    XGS3-S4XG Standard Module for XGS3-42000R with 4-Port 10G XFP
    XGS3-PWR-AC 400watt AC power supply for XGS3-42000R
      Accessories
    MTB-XLR XFP Port 10GBase-LR Fiber Optic Module (Single mode / 1310nm / max. 10km)
    MTB-XSR XFP Port 10GBase-SR Fiber Optic Module (Multi-mode / 850nm / max. 300m)

  • Datasheet

    Date Version Description Download
    2010-06-11 1.0 XGS3-42000R

    Quick Guide

    Date Version Description Download
    2010-05-01 1.0 Initial release for AC Power Supply
    2010-05-01 1.0 Initial release for Modules
    2010-04-23 1.0 Initial release

    User’s Manual

    Date Version Description Download
    2010-06-09 1.0 400watt AC power supply for XGS3-42000R
    2010-05-14 1.1 Initial release for Command Guide.
    2010-05-14 1.0 Initial release for Configuration Guide.

    EC Declaration

    Date Version Description Download
    2010-05-08 1.0 Initial release
      Ordering Information
    XGS3-42000R 4-Slot Layer 3 IPv6/IPv4 Routing Chassis Switch ( with one AC power supply)
    XGS3-M24GX Management Module for XGS3-42000R with 24-Port Gigabit (12-Port Combo) + 1-Port 10G XFP
    XGS3-S24G Standard Module for XGS3-42000R with 24-Port Gigabit (12-Port Combo)
    XGS3-S48G Standard Module for XGS3-42000R with 48-Port Gigabit copper
    XGS3-S48GF Standard Module for XGS3-42000R with 48-Port Gigabit SFP
    XGS3-S4XG Standard Module for XGS3-42000R with 4-Port 10G XFP
    XGS3-PWR-AC 400watt AC power supply for XGS3-42000R
      Accessories
    MTB-XLR XFP Port 10GBase-LR Fiber Optic Module (Single mode / 1310nm / max. 10km)
    MTB-XSR XFP Port 10GBase-SR Fiber Optic Module (Multi-mode / 850nm / max. 300m)

  • Photo Model Description
    MGB-Series Transceiver 1000BASE-SX/LX SFP Transceiver
    Ordering Information
    XGS3-42000R 4-Slot Layer 3 IPv6/IPv4 Routing Chassis Switch ( with one AC power supply)
    XGS3-M24GX Management Module for XGS3-42000R with 24-Port Gigabit (12-Port Combo) + 1-Port 10G XFP
    XGS3-S24G Standard Module for XGS3-42000R with 24-Port Gigabit (12-Port Combo)
    XGS3-S48G Standard Module for XGS3-42000R with 48-Port Gigabit copper
    XGS3-S48GF Standard Module for XGS3-42000R with 48-Port Gigabit SFP
    XGS3-S4XG Standard Module for XGS3-42000R with 4-Port 10G XFP
    XGS3-PWR-AC 400watt AC power supply for XGS3-42000R
    Accessories
    MTB-XLR XFP Port 10GBase-LR Fiber Optic Module (Single mode / 1310nm / max. 10km)
    MTB-XSR XFP Port 10GBase-SR Fiber Optic Module (Multi-mode / 850nm / max. 300m)

Facebooktwittergoogle_pluspinterestlinkedinyoutube